• CompTIA Network+ exam question/answer explanation required!

    Here's an exam question for which the answer is 'C - incorrect subnet mask'. I would be grateful if anyone could explain why C is the correct answer? The question is as follows: A network administrator configures a router with the following IP address information: Gigabit Ethernet 1 Interface:...

    rameznadem5 pointsBadges:
  • Enter the pin from the router label

    Where do I find the pin number on my router label?

    NANITAMBI5 pointsBadges:
  • Internet disconnection problems,can someone help?

    Every 5-10 minutes my internet disconnects for half a minute.I've had the same problem 3 months ago,it lasted for 1 month and then suddenly the internet started to work properly.Now 2 months later the problem returned.The problem is not my device,on other devices i experienced the problem too.Also...

    nokedli1275625 pointsBadges:
  • Router not turning on

    I have a:Netgear N600 Wireless Dual Band Gigabit Router,Model #: WNDR3800.It does not turn on, nor do the lights.It does not reset.I am not sure if the problem is the router itself or the cable that powers it.

    somebodythatiusedtoknow5 pointsBadges:
  • would a port scan hit router or modem?

    i thought a port scan would hit the modem but i heard that it would hit the router what one would it poort scan?

    usernameeeee45 pointsBadges:
  • internet speed

    i pay for 30 download 5 upload i get that much just a little bit faster, but whenever i download on my xbox i get 200Mbps im not kidding but a y other device i get like 32Mbps download only my xbox do i get 200Mbps and i pay for 30. its way faster than i pay but only on my xbox

    usernameeeee45 pointsBadges:
  • Can I use a managed switch to run two LTE Routers at different times?

    Hi, I have a 3COM Superstack 3 4200 28 port manged switch.I also have two Huawei B315 LTE Routers with different sim cards on different networks. Basically I use the one router between 11PM-6PM and the other between 6PM-11PM because of the data plans I have.Is there a way I could set it up to...

    gouwsie695 pointsBadges:
  • my wi-fi password,

    I don't remember my wi-fi password, how do I change my passsword?

    Sugar201115 pointsBadges:
  • What is the difference between a router and a relay agent?

    Hi, Confused between router and relay agent. 1. Can a router broadcast or can a relay agent broadcast. 2.Is relay agent present in all router. 3.when configuring a server 12 to act as relay agent or as a router does it need to be on separate new server or can we configure it with other roles and...

    Robin115 pointsBadges:
  • What is a router?

    what is a router

    Williams355 pointsBadges:
  • How to make same SSID’s to not to interfere

    Hi All. My machine is configured with 2 Access points with same SSID's Aruba AP Hostapd (wlan0_0 ) Whenever my machine connects to Aruba client is supposed to connect Aruba AP if not it should connect to softAp For that I did port down of hostapd say wlan0_0 down whenever we connects to aruba. But...

    NarendraSidharth5 pointsBadges:
  • How do I configure two leased lines in one router?

    How do I configure two leased lines in one router? My D-link router is a unmanaged router.

    rawat1235 pointsBadges:
  • Putting a password into the router

    Could someone tell me how can I put a password into my router?

    jayjoy9225 pointsBadges:
  • Command router EIGRP

    In the command router eigrp 100, what does the value 100 represent?

    michaelsilue5 pointsBadges:
  • Network layer

    If a router uses shadow forwarding table, does each input part get the same shadow table?

    s09311965 pointsBadges:
  • Lotus notes 8.5.3 Server – Want to hold outgoing mail in mail.box – stop delivery

    We want to test a new application and hold any mail it generates. Turned off the router tasks and smtp server tasks - but mail continues to deliver to our other domain servers.

    joyfulljogger5 pointsBadges:
  • Netgear N300 Network Monitoring

    I have a Netgear N300 wireless router. I live in an apartment building and I was wondering if there is a way for me to tell how many computers are connected to my network so I can tell if our neighbors are using our wireless network.

    techineptinVA5 pointsBadges:
  • USB wireless adaptor as input source to router

    I have a USB wireless adapter. I wanted to use it as an ISP input source to a wireless router. This so all my wireless devices can connect to and share internet connection. Have been searching article on this but not much on this topic. Can this be done?

    tran126715 pointsBadges:
  • How do we create a network of 100 Computers in one building from scratch?

    One building, divided in 3 stories. I want to create a network of 100 computers in this one building. How many Routers, Switches and Hubs do I need? How many Straight and cross over cables do I need? and what kind of topologies to implement? Do I need a server? What protocol to implement? What i am...

    fahad8510 pointsBadges:
  • Configuring wireless ethernet router to access PCs across router

    A server controlled networked having wifi router. Router's WAN socket connects to server & some computers connect the LAN & Wi-fi of router. I need proper config details for the router and network to share all PCs (files and printers) across the complete network.

    tanayn5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following