• wireless roaming howto

    I have 3 routers (2 trendnet, dlink) one of trendnet (192.168.100) is connected to my proxy server and i want the other 2 acts as access point and do roaming. I did a setup using same ssid, differents channels but i can't ping to 192.168.10.100 (proxy connected ). What else should i do? Thanks in...

    Tics5 pointsBadges:
  • cisco router 1841

    how to install and connect, cisco router 1841 to pc desktop.? how would i know if it is connected.?

    Dustinlr5 pointsBadges:
  • Routers

    What router component holds routing table, ARP cache, and running config file?

    198234765015 pointsBadges:
  • split static ips between different machines

    I am on a cable connection wiht a 5port switch and a router (wgr614v7) I have my router attached to the switch pulling a DHCP lease from ISP, which runs the majority of my house), and my server is connected to the switch pulling 5 statics off one of the three nics installed. one nic is disabled,...

    Pur3vil5 pointsBadges:
  • Cisco routing problem

    I have a Cisco router (routerA) at a remote site, which connects point-to-point to the HQ site (routerB), and it needs to communicate to another router (routerC) that is connected at the HQ site. From the CLI in routerA I cannot ping routerC, but from a PC located with routerA, I can open a dos...

    Jdleon85 pointsBadges:
  • Cisco Networking

    How can we provide load sharing on single router of two ISPs. plz let us suggest on the same.

    Bhupendra205 pointsBadges:
  • Connect Wireless G ADSL2+ router with Access Point

    i have a d-link wireless g adsl2+router dsl-2640u connect direct to phone line with : ssid=blink ip= 192.168.1.1 wep=0022b0c2cd61 so, i dont have the user name and password for administrator to logon and change the wep code. but,when i connect to access point, the wep of access point didnt take the...

    Army125 pointsBadges:
  • Cisco: Setting a VLAN across a network

    hi,newbie here :) I am working on Packet Tracer 5.0 and I want to setup 2 vlan's that spread across a network. I attach the view of the network: 2 of 3 hosts on switch 1 belong in vlan10 and the other one belongs to vlan20. Likewise, 2 of 3 hosts on switch 2 belong to vlan10 and the other one...

    Teo20 pointsBadges:
  • BGP setting in Cisco 2811 router

    how to configure bgp in cisco 2811

    Alerese5 pointsBadges:
  • Expanding Wi-Fi Network Coverage

    I am just learning now how wifi works. My question is the following: If I configure a Wireless Router in N mode to maximize the range of the coverage of the router, the only wireless that can connect to the wifi router is only those with N wireless card or the G wireless card can get connected even...

    CanitoCool5 pointsBadges:
  • Cisco 2811 – Divide Bandwidth

    We have Cisco 2811 router with on serial interface and two fast ethernets. We planned to take 1 mbps leased line and we have to divide it into two parts. For one network is should be 300 kbps and the rest bandwidth for another network. Can any help in this.

    PSKR20 pointsBadges:
  • How to set up a Cisco ASA 5505 VPN using the client behind a Cisco 1841 router using the serial interface

    how to set up a cisco asa 5505 vpn using the client behind a cisco 1841 router using the serial interface

    Sparky42wv5 pointsBadges:
  • Internet configuration problem with router

    i have 2 NIC on my server the 1st NIC access internet from router 2nd NIC conect local area net work but the client doesent acces internet. when i fonfigure manualy the router addres in to the clinet the internet will be functuonal but i need the client access automatical internet please help me...

    Bobmarley25 pointsBadges:
  • I can’t ping my default gateway with D-link 2600 router

    i m having prblm with my office router i cnt ping to my routers ip nd i dnt know D-link router command so i just wnt to know the command of to up the ethernet port would you like to help me? mail me on sumitcj@yahoo.com waiting for your help.

    Sumitcj5 pointsBadges:
  • Cisco 2960 link aggregation with Foundry

    How do i setup a 2960 link-aggregate with Foundry?

    NC11655 pointsBadges:
  • Cisco 2811 PVDM2-24DM Initialising

    Dear All Professionals, We have taken on the installation of a Cisco 2811 to make digital communications over ISDN and are requiring assistance with our hardware configuration . We have all the necessary modules and so on however our current problem is: We have the digital modem module in slot 0...

    Jtrade5 pointsBadges:
  • Configuring the DHCP server behind the router for 3 networks

    Network 1 (192.168.50.0/24)---"Router"---"Switch or bridge"---"DHCP Server" Network 2 (172.16.0.0/24)______|| Network 3 (10.0.0.0/24)_________| how should i config DHCP server so every client's IP in all 3 networks can be assign by DHCP?

    Yugioh885 pointsBadges:
  • Router configured one hop from PC with default gateway as IP address

    What would happen and what would be the flow if I configured a PC with the default gateway as an IP address of the router that is one hop away -- that means, I have one more router in between?

    NetworkingATE1,545 pointsBadges:
  • Rerouting traffic requests based on destination IP range

    Hi there Here is my situation: I have got a DSL connection with public ip addresses at my office. I have a client with a DSL connection with dynamic ip address, at his office. The DSL connection at my office can access any internet sites. The DSL connection at my client can only access sites local...

    PsiTorn5 pointsBadges:
  • About router

    I have two lease line but one router cisco 2600 series , how can i configure,at the same time both are working

    Riyaz10 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following