• Configuring OSPF to speed up internal traffic with Cisco 1800?

    How can I configure OSPF to speed up our internal traffic using a Cisco 1800? What information do I need to begin with? Does it need to be installed on all routers? Or just one?

    NewnanIT1,110 pointsBadges:
  • Cisco Router configuration

    I would like to know all the configurations and changes that can be done in a router.

    Shehzanessak5 pointsBadges:
  • Cisco router 2821 configuration NAT and DHCP

    I trying to make it works but still to no avail. Maybe somebody can help me with my problem. I configure my router 2821 with 2 Gic interface and 16 ports fastethernet. Here's what I need to accomplish: Int Gi 0/0 WAN-outside Int Gig0/1 LAN-inside VLAN 5 DHCP  (another network) Note: LAN users can...

    Bonsan15 pointsBadges:
  • Dumping 7 Cisco routers on a LAN simultaneously?

    Is there a method to dump the configuration of seven Cisco routers on a LAN at the same time?

    TeachMeIT975 pointsBadges:
  • Load balance on WAN interface using static router between two ISP

    By using static router, i need to configure two lease line of 3 mbps and failover

    Pranab12310 pointsBadges:
  • what command is used to configure the console port on a router

    what command is used to configure the console port on a router

    Funlvr196510 pointsBadges:
  • Solution other than MPLS with Leased Line Link

    We have MPLS managed services provided by the ISP. CE router connects to our router with L3 link and we are running OSPF on L3 links connected to CE routers. Earlier we had leased lines and we could use multiple leased lines with load balancing and high availability, terminated on the same router....

    Eesh125 pointsBadges:
  • How to configure two default gateways to be 2 ISP (PIX 525)

    I have a network as follows: PIX Firewall 525 uses three network interface Ethernet1, Ethernet2, Ethernet3. E1 (10.0.0.1, Inside) connected to LAN E2 (117.16.126.35, Outside) connected to the modem (117.16.126.33) ISP1 (This address by the ISP level) E3 (192.168.1.2, Outside2) connected to the...

    Arowana200015 pointsBadges:
  • Connecting two routers on the same network to extend range

    Can I connect 2 wireless routers on the same network to extend the range of the network? What changes will I have to make and what routers would you recommend?

    ITKE1,145,755 pointsBadges:
  • Telnet to a Cisco 1700 Router

    I have a cisco 1700 router, when I telnet to it from a remote site, it comes back saying "connection closed by remote host". I have checked the vty lines and verified the password. even more interesting is that when I telnet to it when directly connected via ethernet, it allows me to connect....

    Bahlezi140 pointsBadges:
  • Load Balancing of Unequal Ethernet Bandwidth

    Is it possible to aggregate and then load balance the unequal ethernet circuits like so: I have two ethenet circuits on my Cisco router. Both have equal costs to the next hop. Ethernet Circuit #1- 200M Ethernet Circuit #2 - 100M Can I aggregate both ethernet circuits so that the total amount of...

    Hcandy5 pointsBadges:
  • Router Re-Configuration

    When I type the IP address of my router in the Explorer address bar. It replies this web page cannot be opened. IP address 198.162.1.2

    Samdog5 pointsBadges:
  • network problem

    Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router

    Krishnabthapa5 pointsBadges:
  • How can i telnet to a cisco 1700 series from a remote host

    Hello can anybody tell me  How i can telnet to a cisco 1700 series from a remote site.?

    Adex005 pointsBadges:
  • how can we configure a 36 port router?

    how to install, configure and use a cisco 36 port router?

    Arun2gautam5 pointsBadges:
  • configuration of a new router

    I WAS CONFIGURING A FRESH/NEW RUTER OF CISCO SERIES 1841 FROM A CONSOLE ON A HYPER TERMINAL.THE ROUTER WAS BROUGHT IN ROMMON MODE AND WRONGLY TYPED CNFREG-REGISTRY 1024 AND GIVEN THE COMMAND.AFTER THIS COMMAND ROUTER STOPS ACCEPTING KEY COMMAND AND HYPER TERMINAL BECAME BLANK .I SWITCH OFF THE...

    VADERA10 pointsBadges:
  • WAN configuration

    how configure the central router in central office? how configure the router in remote branch office ? please,give me a sample configuration of central router configuration in central office. LINE :E1 FOR CENTRAL OFFICE BANDWIDTH OF BRANCH OFFICES:256 KBPS ROUTER IN CENTRAL OFFICE : CISCO 3800...

    Alioroumi5 pointsBadges:
  • Cisco 2811 Fast Ethernet and LAN configuration

    i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

    JACK15705 pointsBadges:
  • VPN Pass-Through Cisco 871

    Hi All, I'm trying to setup VPN pass-through on a Cisco 871 router.  I have to admit, I'm not very knowledgeable on VPN, let alone doing it on a Cisco router.  I referenced a Cisco document building this config, but can't seem to get it to work. Here's where I am currently at:  I can access the...

    Nfantis55 pointsBadges:
  • how to configure PA-MC-STM1 card in cisco 7206 router

    I want to know how to configure PA-MC-STM1  card in cisco 7206 router

    ITKE1,145,755 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following