• Where can I find Cisco 2801 regulatory certificates

    where can I find cisco 2801 regulatory certificates

    Edisonacuna5 pointsBadges:
  • Cisco 2811 Power Supply Jumper – PS Type

    I have replaced a DC supply with an AC 100V but the new power supply doesn not havbe anywhere for the PS Type Jumper connection. What does the PS Type do and can I operate without that connected (as the new power supply has no connector) ? Thanks in Advance.

    Greencj35 pointsBadges:
  • load balance on WAN interfaces

    How can I set up two 2811 routers coneected together with two leased lines with load balance. There are two 2M leased lines to form a 4M leased line for operation.

    Cmcheng5 pointsBadges:
  • Cisco’s 2500 series router and WAN card serial interface differences

    What is the difference between the serial interface of 2500 series Cisco routers and the serial interface of WAN cards (WIC-1t)? If there is no difference then is there any data-rate difference between the above two serial interfaces?

    NetworkingATE1,545 pointsBadges:
  • 4 VLANS, 3 locations, 3 Routers, No communication between Lans or VLANs

    OK, here is my problem, I'm working on a project in the Test phase right now. I have 3 routers (Cisco 2811s), all running EIGRP, these are seperating 3 goegraphical regions. Each of these Routers is linked via Trunking line to a Switch which has 4 VLANs enable. According to everything I have found...

    CRagsdale32755 pointsBadges:
  • Configuring Cisco 1700 with Cyberoam box

    This is regarding the Cisco 1700 series router, which has been configured by some other experts. We are now having a lease line and the Cisco router connected with Cyberoam box. Earlier we had an ADSL connection, so I had direct IP where there was no need to logging into Cyberoam everytime. But...

    NetworkingATE1,545 pointsBadges:
  • How to add a subinterface in Cisco 2811 router

    how to add a subinterface in router 2811

    Fsheb5 pointsBadges:
  • configuring two adsl2+ line on cisco router1841

    I have cisco router 1841 with one adsl2+ connected to it, i need to connect another adsl2+ line to this router for the purpose of load balancing, i am using statiic ip routing, t Could you please let me know the complete configuration to attach new adsl2+ line to this router, As i am at beginner...

    Jaggum5 pointsBadges:
  • Cisco 2811 router with Ethernet access to MPLS

    Can a Cisco 2811 router support a 40Mbps MPLS connection using Fast Ethernet access?

    Webonauta15 pointsBadges:
  • Need your help to connect remote sites

    I have 4 cisco 800 routers i have configured with NAT and DHCP and they are all connected to the internet via satellite. I have a database server that i want remote sites to access it has an ip 192.168.0.2. All the four LAN'S are on the network 192.168.0.0 255.255.255.0 and they are behind a public...

    Kenweed5 pointsBadges:
  • How do you configure IOS to output the logs on the VTV line?

    Logged on to Cisco IOS via VTV and entering debug command but got no output from the logs. How do you configure the device to output the logs on the VTV line?

    NetworkingATE1,545 pointsBadges:
  • What command to see how many times the particular link is down/up in Cisco 3845 router?

    What command can I use to see how many times the particular link is down and up in Cisco 3845 series router in cap side? For example: s1/0:12 and how to know in branch side in 1800 series router exp-s0/1/0

    NetworkingATE1,545 pointsBadges:
  • Putting it together Cisco Router and Switch

    can someone please tell me how to get a cisco router and a cisco switch hooked up to my home network so it can be my lab with access to the outside world via my home network non-cisco router? I'm tired of pulling my hair out.

    Rob1715 pointsBadges:
  • in a cisco router what does he following configuration statement mean

    in a cisco router what does he following configuration statement mean s 0.0.0.0.0.0.0.0 serial0

    Fsrock35 pointsBadges:
  • Routing Virtual IP Address.

    We have 2 Windows 2003 Terminal Servers and both are part of load balance with a Single Virtual IP Address. For Eg 192.170.2.34 is virtual ip, and any User tries to connect to this ip address will be diverted to any one Server IP eg 192.179.2.33 or 192.170.2.32. accoring to load. But when users...

    Mysore0 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following