-
I have a cisco 1700 router, when I telnet to it from a remote site, it comes back saying "connection closed by remote host". I have checked the vty lines and verified the password. even more interesting is that when I telnet to it when directly connected via ethernet, it allows me to connect....
Last updated: -
Load Balancing of Unequal Ethernet Bandwidth
Is it possible to aggregate and then load balance the unequal ethernet circuits like so: I have two ethenet circuits on my Cisco router. Both have equal costs to the next hop. Ethernet Circuit #1- 200M Ethernet Circuit #2 - 100M Can I aggregate both ethernet circuits so that the total amount of...
Last updated: -
Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router
Last updated: -
how can we configure a 36 port router?
how to install, configure and use a cisco 36 port router?
Last updated: -
How can configure two Internet LL (Primary and backup)on same cisco router 2600 (2 Serieal and 4 ethernet ports). ISP 1 - 4Mbpes and ISP 2 - 1 Mbps.
Last updated: -
Cisco 2811 Fast Ethernet and LAN configuration
i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.
Last updated: -
WCCP step by step setup and utilisation of Cisco Cache engine or Baracuda
I am new to this field and would like assistance of setting up WCCP on a Router and two content engines, Baracuda and cisco Cache engine. Please help?
Last updated: -
how to configure PA-MC-STM1 card in cisco 7206 router
I want to know how to configure PA-MC-STM1 card in cisco 7206 router
Last updated: -
SSH configuration on Cisco router
Please provide me a step to step detail configuration of SSH. Thanks..
Last updated: -
Problems witih Cisco AP Aironet 1231AG
hello! i have done something very stupid...I erased cisco IOS image and now when i connect via com port and set up the ip address, netmask and default router, i still cannot connect to the AP i can't even ping the AP, and in order to upload other image i must be connected to it via tftp but every...
Last updated: -
how to install and connect, cisco router 1841 to pc desktop.? how would i know if it is connected.?
Last updated: -
Bandwith for lan segment into wan serials
I have two cisco 2800 routers, and need to assign diferent bandwith to diferent lans, that send data into these two equipments, what is the best form to config this?
Last updated: -
I have a Cisco router (routerA) at a remote site, which connects point-to-point to the HQ site (routerB), and it needs to communicate to another router (routerC) that is connected at the HQ site. From the CLI in routerA I cannot ping routerC, but from a PC located with routerA, I can open a dos...
-
How can we provide load sharing on single router of two ISPs. plz let us suggest on the same.
Last updated: -
I inherited a network that has a Cisco 2811 router setup with the following: interface FastEthernet0/0 no ip address no ip route-cache cef no ip route-cache duplex full speed 100 ! interface FastEthernet0/0.18 description Data VLAN encapsulation dot1Q 18 native ip address 10.221.18.1 255.255.255.0...
Last updated: -
Cisco: Setting a VLAN across a network
hi,newbie here :) I am working on Packet Tracer 5.0 and I want to setup 2 vlan's that spread across a network. I attach the view of the network: 2 of 3 hosts on switch 1 belong in vlan10 and the other one belongs to vlan20. Likewise, 2 of 3 hosts on switch 2 belong to vlan10 and the other one...
Last updated: -
BGP setting in Cisco 2811 router
how to configure bgp in cisco 2811
Last updated: -
We have Cisco 2811 router with on serial interface and two fast ethernets. We planned to take 1 mbps leased line and we have to divide it into two parts. For one network is should be 300 kbps and the rest bandwidth for another network. Can any help in this.
Last updated: -
Share two broadbanc connections in 2811 router
I am having a 2811 router with one Serial interface and two Fe. We have two broadband connections. Can any one help how to configure router with these specifications. Thanks in advance
Last updated: -
how to set up a cisco asa 5505 vpn using the client behind a cisco 1841 router using the serial interface
Last updated: