running config

Nov 18 2009   1:06PM GMT

How to archive your Cisco Router or Switch Configuration?

Posted by: Yasir Irfan
Cisco Router tips, Cisco Switches tips, Cisco Tips, Network Tips, Cisco IOS tips, archive command, archive config, configure replace flash, IOS version 12.3 (4) T, IOS Version, Cisco Systems, Cisco Routers, Cisco Switches, Cisco IOS configuration, Cisco Configuration, Router Configuration, Network Technologies and Trends, running config, FTP, HTTP, HTTPS, RCP, SCP, TFTP, protocols, How to archive your Cisco Router or Switch Configuration?

Do you all know there is a great way to archive the tasks you carry out in your Cisco Router or a Cisco Switch? Especially whenever you perform a “write memory or copy run start” in your Cisco Router or a Cisco Switch.

Most people do not realize starting an IOS version 12.3 (4) T and higher an “archive” and “archive config” commands were introduced by Cisco Systems.

The main advantage of advantage of an “archive” command is to have incremental backups of your Cisco Router or Switches configurations and for some reasons if you have blowup with the configuration then using the this feature you can retrieve the old configuration file into your Cisco router or switch.

The “archive config” command allows you to save Cisco IOS configurations in the configuration archive using a standard location and filename prefix that is automatically appended with an incremental version number (and optional timestamp) as each consecutive file is saved.
Once the maximum number of file saved in the archive, the oldest file will be automatically replaced by the next file.

The “show archive” command displays information for all configuration files saved in the Cisco IOS configuration archive.
In this example, we will save the archive configuration files on the flash memory; however, you can also store the configuration files remotely using such protocols as FTP, HTTP, HTTPS,RCP, SCP, and TFTP.
By using following set of commands we can enable archive feature in a Cisco Router or a Cisco Switch provided the IOS version is either 12.3 (4) T or higher . In this example, the location and filename prefix is specified as disk0: itkebackup

ITKE-AS0 (config)#archive

ITKE-AS01(config-archive)#path flash:itkebackup

To save the current running configuration in the configuration archive use the “archive config” command as shown below

ITKE-AS01# archive config

The “show archive” command displays information of the files saved in the configuration archive as shown in the following example:

ITKE-AS01#show archive

         There are currently 3 archive configurations saved.

         The next archive file will be named flash: itkebackup -3

         Archive # Name

         0

         1 flash: itkebackup -1

         2 flash: itkebackup -2 <- Most Recent

         3

         4

         5

         6

         7

         8

         9

         10

         11

         12

         13

         14

 

ITKE-AS01#

By using the “configure replace flash” command you can restore the configuration

ITKE-AS01#configure replace flash: itkebackup -2

         This will apply all necessary additions and deletions

         to replace the current running configuration with the

         contents of the specified configuration file, which is

         assumed to be a complete configuration, not a partial

         configuration. Enter Y if you are sure you want to proceed. ? [no]: y

         Total number of passes: 0

         Rollback Done

The “archive” command is quite handy to keep the he is great for keeping multiple copies of the running config in an archive.

Sep 12 2009   7:34AM GMT

How to capture a text using PuTTY client?

Posted by: Yasir Irfan
PuTTY, Telnet, SSH, Telnet Client, Backup, running config, Startup config, Cisco Router, Cisco Switch, Cisco Tips, Cisco backup

 

PuTTY doesn’t need any introduction as its one of the widely used for remote console utility. PuTTY is an SSH and telnet client.

In day to day operational activities we do telnet or SSH to our Cisco routers or Switches, at times we need to backup a running or startup config or   a Cisco router or a switch or even some times we need to capture the terminal session logs for technical information etc.  This is can be easily done by using the PuTTY client.

I will show you how to capture a text using PuTTY client.

Once you have established a remote session with a Cisco router or a Switch, follow the following steps

 

Step 1: Right Click on the menu bar and select “Change Settings”

 

Step 2: Click logging under the icon Session.

 

Step 3: Then select “All Session Output”.

 

Step 4: Select the location using the browse button and enter the desired file name and click apply.

 

These steps will create the log file in the specified location and it will log everything you did in that particular telnet or SSH session.