Network technologies and trends » Cisco Catalyst 6506-E Switch

How to configure HRSP between Nexus 7000 and Cisco Catalyst 6500 Series Switches?

Yasir Irfan — Sun, 22 May 2011 05:15:13 +0000

Configuring HRSP in a Cisco Nexus 7000 Series Switch is often an easy task and it takes slight different approach. Recently we had some issues in our Data Centre and then I was forced to configuring the HSRP between a Cisco Nexus 7010 Switch and Cisco Catalyst 6506 E Switch. The configuration was quite simple, I would like to share the steps need to configure HSRP between a Cisco Nexus 7000 Series and Cisco Catalyst 6500 Series Switches.

In the below example I will configure HRSP for VLAN 34 with a subnet of 10.204.34.0/24

Cisco Catalyst 6500 Series Switch Configuration

Step 1 – Create VLAN 34 in Cisco Catalyst Switch and assign an IP Address

MBGF-DAC-6500-BB01(config)#interface vlan 34

MBGF-DAC-6500-BB01(config-if)#ip address 10.204.34.3 255.255.255.0

Step 2 – Configure HSRP group id, priority and timers, my active switch will be Cisco 6500 Switch due to its priority

MBGF-DAC-6500-BB01(config-if)# standby 34 ip 10.204.34.1

MBGF-DAC-6500-BB01(config-if)# standby 34 timers 1 3

MBGF-DAC-6500-BB01(config-if)# standby 34 priority 150

MBGF-DAC-6500-BB01(config-if)# standby 34 preempt

Cisco Nexus 7000 Series Switch Configuration

Step 1 – Create VLAN 34 in Cisco Nexus Switch and assign an IP Address

VDC-Admin-AG01-MB-1256-002(config)# interface vlan 34

VDC-Admin-AG01-MB-1256-002(config-if)# ip address 10.204.34.2/24

Step 2 – Configure HSRP group id, priority and timers , Nexus will be in standby mode

VDC-Admin-AG01-MB-1256-002(config-if)#hsrp 34

VDC-Admin-AG01-MB-1256-002(config-if-hsrp)# priority 110

VDC-Admin-AG01-MB-1256-002(config-if-hsrp)# timers 1 3

VDC-Admin-AG01-MB-1256-002(config-if-hsrp)# ip 10.204.34.1

Verify the HSRP States

Cisco Catalyst 6500 Switch Status

MBGF-DAC-6500-BB01:1#sho standby brief

P indicates configured to preempt.

Interface Grp Prio P State Active Standby Virtual IP

Vl34 34 150 P Init local 10.204.34.3 10.204.34.1

MBGF-DAC-6500-BB01:1#

Nexus 7000 Series Switch HSRP Status

VDC-Admin-AG01-MB-1256-002# sho hsrp group 34

Vlan34 – Group 34 (HSRP-V1) (IPv4)

Local state is Standby, priority 110 (Cfged 110)

Forwarding threshold(for vPC), lower: 1 upper: 110

Hellotime 1 sec, holdtime 3 sec

Next hello sent in 0.179000 sec(s)

Virtual IP address is 10.204.34.1 (Cfged)

Active router is 10.204.34.2

Standby router is local

Virtual mac address is 0000.0c07.ac22 (Default MAC)

2 state changes, last state change 2d18h

IP redundancy name is hsrp-Vlan34-34 (default)

VDC-Admin-AG01-MB-1256-002#

Configuring HRSP is a quite a simple and if you are facing any problems configuring you can post your scenario in the comments area of this post.

How to configure an interface to default settings in a Cisco Switch or a Cisco Router?

Yasir Irfan — Sat, 13 Dec 2008 06:27:03 +0000

This is a cool command to erase just the configuration for a particular interface in a Cisco Switch or a Cisco Router.

In the following example we will configure the interface fast Ethernet 0/9 to default configuration

Current Configuration for fast Ethernet 0/9

ITKE-Cisco#sho running-config interface fastEthernet 0/9

Building configuration…

Current configuration : 85 bytes

interface FastEthernet0/9

switchport access vlan 100

switchport mode access

end

ITKE-Cisco

Now we will configure the fast Ethernet 0/9 to default configuration using the following command

“default interface fastEthernet 0/9”

ITKE-Cisco#configure t

Enter configuration commands, one per line. End with CNTL/Z.

ITKE-Cisco(config)#default interface fastEthernet 0/9

Interface FastEthernet0/6 set to default configuration

ITKE-Cisco(config)#

Running configuration for fast Ethernet 0/9 after configuring to default settings

ITKE-Cisco#sho running-config interface fastEthernet 0/9

Building configuration…

Current configuration : 68 bytes

interface FastEthernet0/9

switchport mode dynamic desirable

end

ITKE-Cisco#

How to configure SPAN(Switched Port Analyzer ) feature in a Cisco Catalyst Switch

Yasir Irfan — Tue, 02 Dec 2008 07:30:23 +0000

It’s quite important for Network Engineers and an essential network troubleshooting technique to utilize the ability of Cisco Catalyst Switches to mirror the traffic and send it to a sniffer for analysis. All Cisco Catalyst Switches support the Switched Port Analyzer (SPAN) feature. The SPAN copies traffic from the specified interface or VLANs and mirrors this traffic to a specified destination interface (SPAN interface). Then you can connect the PC with a sniffing tool (Wireshark) installed on the destination SPAN interface to capture all the mirrored traffic.Let’s see how to configure the SPAN in Cisco Catalyst Switches. To enable the switch SPAN mirroring feature configure the following on the catalyst switch: Configuration Example – Monitoring traffic from a specific interfaceITKEAS01#configure tITKEAS01(config) monitor session 1 source interface gigabitEthernet 0/5

ITKEAS01(config)#monitor session 1 destination interface gigabitEthernet 0/10

The above configuration will capture all traffic from interface gigabitEthernet 0/5 and send it to SPAN port interface gigabitEthernet 0/10

Configuration Example – Monitoring an entire VLAN traffic
ITKEAS01(config)#monitor session 1 source vlan 100
ITKEAS01(config) monitor session 1 destination interface gigabitEthernet 0/10 The above configuration will capture all traffic of VLAN 100 and send it to SPAN port interface gigabitEthernet 0/10

Use show monitor session 1 to verify your configuration.

How to configure DHCP Snooping in a Cisco Catalyst Switches.

Yasir Irfan — Sat, 22 Nov 2008 12:56:06 +0000

So here we go, with the configuration of DHCP snooping on a Cisco Switch. This feature protects the network by allowing the Cisco Switches to accept DHCP response message only from the authorized servers connected to the trusted interfaces in a Cisco Switch.

All Switch to Switch connections are configured as 802.1 1Q Trunk ports.

IP Address and HSRP Details for the Core Switches From the above scenario we have two Cisco 6513 Series Switches as a Core/ Distribution with three VLANS one for management of Switches VLAN 50,VLAN 100 for all the servers and VLAN 101 for clients. Two Cisco 3560 Series Switches as Server Farm Switches and a Cisco 3560 Series Switch as an Access Switch.There are two DHCP servers with an IP address 10.0.1.100 and 10.0.1.101 connected with Server Farm Switches with HP NIC teaming. We configure DHCP Snooping based on above scenario.

The first step to configure DHCP Snooping is to turn on DHCP snooping in all Cisco Switches using the “ip dhcp snooping” command.

All Cisco Switches (config)#ip dhcp snooping Second step is to configure the trusted interfaces, from the above scenario all trunk ports are configured as trusted ports as well as the interfaces G0/7,(ITKESF01 50.0.0.6), G0/17,(ITKESF02 50.0.0.7), G0/9 ITKESF01 50.0.0.6) and G0/18 ITKESF02 50.0.0.7) connected to DHCP servers with IP 10.0.1.100 and 10.0.1.101. Lets configure all trunk ports in ITKEBB01

ITKEBB01(config)#interface range gigabitEthernet 3/21 – 23

ITKEBB01 (config-if)#ip dhcp snooping trust

Now let’s configure all trunk ports in ITKEBB02

ITKEBB02(config)#interface range gigabitEthernet 3/21 – 23 ITKEBB02 (config-if)#ip dhcp snooping trust

ITKEBB02 (config)#interface gigabitEthernet 3/16

ITKEBB02 (config-if)#ip dhcp snooping trust

Now let’s configure the trusted ports for the DHCP servers

ITKESF01(config)#interface gigabitEthernet 0/7

ITKESF01 (config-if)#ip dhcp snooping trust

ITKESF01(config)#interface gigabitEthernet 0/17 ITKESF01 (config-if)#ip dhcp snooping trust

ITKESF02(config)#interface gigabitEthernet 0/9

ITKESF02 (config-if)#ip dhcp snooping trust

ITKESF02(config)#interface gigabitEthernet 0/18 ITKESF02 (config-if)#ip dhcp snooping trust

Now let’s configure the trunk ports Access Switch ITKEAS01

ITKEAS01(config)#interface range gigabitEthernet 0/49 – 52

ITKEAS01 (config-if)#ip dhcp snooping trust

Finally we are going to configure VLANS for DHCP snooping DHCP snooping will used on all the VLANs (VLAN 100 & 101)except management VLAN 50 . Also we will limit the requests rate received in the Access Switch (ITKEAS01) ALL SWITCHES(config)# ip dhcp snooping VLAN 100,101

ITKEAS01(config)#interface range gigabitEthernet 0/1 – 48

ITKEAS01 (config-if)#ip dhcp snooping limit rate 20

Displaying the DHCP snooping

For further reference please do check this article from Cisco about DHCP snooping.

What is Dynamic Host Configuration Protocol (DHCP) Snooping?

Yasir Irfan — Thu, 20 Nov 2008 07:54:05 +0000

Dynamic Host Configuration Protocol (DHCP) Snooping is a security feature which filters untrusted DHCP messages, this security feature can protects the devices on the network from associating with an unauthorized DHCP server. When the Dynamic Host Configuration Protocol (DHCP) Snooping feature is enabled on a Cisco Switch , the Cisco Switch builds a table of MAC address, IP address lease time , binding type and interface information. In coming posts I will try to explain to how to enable and configure the Dynamic Host Configuration Protocol (DHCP) snooping security feature in a Cisco Switch.

In which slot shall we install the Supervisor Engine in Cisco 6500 Series Catalyst Switches -Series2

Yasir Irfan — Mon, 17 Nov 2008 05:16:17 +0000

Dear Friends in one of my previous post I did explained in which slot the Supervisor Engine SUP720 to be installed in a Cisco 6500 Series Switches. Now let’s proceed further and figure out in a Cisco Catalyst 6506-E Switch, in a Cisco Catalyst 6506-E Switch the Supervisor Engine SUP720 is either installed in slot 5 or 6.

Don’t panic whenever you see %IP-4-DUPADDR: Duplicate address error log in your Cisco 6500 Switches running HSRP

Yasir Irfan — Sun, 09 Nov 2008 06:51:50 +0000

If you are running HSRP and one of your VLAN is down and the following errors are generated in your Switch don’t panic. All this happens due the Trojans in the network.

MBGF-DAC-6500-BB01#sho log

Nov 9 07:54:21: %IP-4-DUPADDR: Duplicate address 10.12.0.2 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:54:52: %IP-4-DUPADDR: Duplicate address 10.12.0.2 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:55:22: %IP-4-DUPADDR: Duplicate address 10.12.0.2 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:55:52: %IP-4-DUPADDR: Duplicate address 10.12.0.2 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:56:11: %SEC-6-IPACCESSLOGS: list 12 permitted 10.0.0.1 256 packets

Nov 9 07:56:22: %IP-4-DUPADDR: Duplicate address 10.12.0.2 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:56:52: %IP-4-DUPADDR: Duplicate address 10.12.0.1 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:57:11: %SEC-6-IPACCESSLOGS: list 12 permitted 10.0.0.2 263 packets

Nov 9 07:57:11: %SEC-6-IPACCESSLOGS: list 12 permitted 10.0.0.7 200 packets

Nov 9 07:57:22: %IP-4-DUPADDR: Duplicate address 10.12.0.1 on Vlan106, sourced by 000f.fe0a.1fbc

Nov 9 07:57:52: %IP-4-DUPADDR: Duplicate address 10.12.0.2 on Vlan106, sourced by 000f.fe0a.1fbc

MBGF-DAC-6500-BB01#

Last week at 3 A.M I received a call from our Help Desk, stating our applications are not running in one our departments. I logged remotely to our Network and try figured out what is problem. Upon carefully looking at the logs in our Cisco 6513 core Switches I figured out a duplicate IP address is created which happens to be the Standby IP address for the Core Switch for HSRP.

I figured out the PC by looking the at mac address generated in the log and closed the network connection for that particular PC and the problem was solved.

If you face similar problems its better to change the HSRP Standby IP address in Core Switches and then try figure out the infected PC. Once the PC is figured out close the network connection and make sure the Trojans are removed. Upon cleaning the infected PC you can reconfigure the HSRP Standby IP address to the previous one.

Once I get the complete solution to fix this problem I will post it.

In which slot shall we install the Supervisor Engine in Cisco 6500 Series Catalyst Switches -Series1

Yasir Irfan — Sun, 26 Oct 2008 05:55:38 +0000

Dear Friends the Cisco 6500 Series Catalyst Switch comes in different models like Cisco Catalyst 6503-E Switch, Cisco Catalyst 6506-E Switch, Cisco Catalyst 6509-V-E Switch, Cisco Catalyst 6509-E Switch and Cisco Catalyst 6513 Switch. But is there any specific slot assigned in these switches to install the Supervisor Engine SUP720? Yes there are specified slots assigned to install the Supervisor Engine SUP720 in any of the Cisco 6500 Series Switches.

Picture Courtesy: Cisco Systems

Now let’s find out these details,

The Cisco Catalyst 6503-E Switch comes with three slot chassis. In the Cisco Catalyst 6503-E Switch the first two slots are reserved for Supervisor Engine SUP720, if you have one Supervisor Engine SUP720 then you can install the Supervisor Engine SUP720 module either in slot 1 or slot 2.

I will cover these details for other models in my next post.