The Journey of a Network Engineer:

how


August 18, 2013  12:15 AM

How to configure Cisco DMVPN? Part-1



Posted by: Sulaiman Syed
ARP, Cisco, Configure, DMVPN, how, mGRE, route, Tunnel, vpn

Configuring Site-to-Site VPN although straight forward, but it fails to scale. just imagine how many tunnels should be created to connected to 10 sites, specially if...

February 13, 2012  10:33 AM

How to configure VRF-lite?



Posted by: Sulaiman Syed
CCIE, Cisco, Configure, forwarding, how, routing, to, virtual

VRF-lite is as the name says, light version of VRF. What is VRF? It is Virtual Routing and Forwarding. It is a logical way of segregating network traffic. Mostly used with

Bookmark and Share     0 Comments     RSS Feed     Email a friend


December 14, 2011  12:26 AM

How to configure per-vlan QoS in Cisco 3550 and 3560



Posted by: Sulaiman Syed
3550, 3560, CCIE, Cisco, class-map, Configure, how, Lab, mark, nested policy, parent policy, per-vlan, police, policy-map, QoS, rate, switch, to, vlan

You might think that configuring QoS in Cisco Switches will follow the same syntax. That what I thought till i started studying CCIE. Let's See one major difference in how policing is implemented on these two platforms. Cisco Catalyst 3550 I find the configuration of 3550...


December 9, 2011  1:33 AM

How to traffic shape Frame-Relay? – part 2



Posted by: Sulaiman Syed
?, adaptive, CCIE, data, how, legacy, map-class, mqc, QoS, shaping, to, traffic, voice

In How to traffic shape frame-relay? part 1 , i have mentioned four types of QoS mechanism that can be applied to frame-relay interface. Lets have a look at the other two...


November 29, 2011  1:29 AM

How Rendezvous Points (RP) Chosen in Auto-RP Multicast Domain?



Posted by: Sulaiman Syed
auto-rp, CCIE, Cisco, dense, how, MA, multicast, Rendezvous Point, RP, sparse

IP Multicast can work on Dense, or Sparse Mode. Dense, where all multicast traffic is flooded out of all the interfaces other than the one it came from (split horizon). It is easy to configure, and there are no planning with it. The down side is, it might create congestion in the network. Specially...


November 23, 2011  10:02 AM

How to configure route dampening in BGP



Posted by: Sulaiman Syed
CCIE, dampening, flap, half-life, how, map, route, router, to

Flapping routes are bad news in BGP. flapping routes are the routes that go up and down in very short time. they are bad news cause they require changes in routing table. routing table that consists of 100 thousand routes cause high load on router. a flapping route will: 1- change the table by...


November 20, 2011  3:11 AM

How to configure Path Variables for BGP aggregation route?



Posted by: Sulaiman Syed
Aggregation, Attribute, CCIE, Cisco, how, Path, route-map, router, to, variables

Using route aggregation (summary) is one of the important tools with BGP. it provides a strong foundation to keep the routes from flapping, or making rapid changes within the BGP backbone cloud. but what if we want to advertise the aggregation with different AS Path variables? as it is known BGP...


November 10, 2011  7:35 PM

How to add reliable default route with RIP?



Posted by: Sulaiman Syed
CCIE, Cisco, how, monitor, reliable, RIP, route, router, static, to, track

Adding reliable default route with RIP The command for distributing a default route into RIP process is very straight forward.  Lets go with the syntax straight away.

router rip default-information originate route-map RELIABLE ! route-map...


November 7, 2011  4:35 AM

How to filter routes in RIP?



Posted by: Sulaiman Syed
CCIE, Cisco, distribute-list, how, loop, prefix-list, RIP, route, router, to

Filtering routes in RIP Although rip is not the best routing protocols, the mechanism of filtering routes can be applied to other routing protocols a well. My personal advice will be to stay away as much as possible from RIP. RIP is a routing loop magnet, you never know when you...


November 3, 2011  9:06 AM

How to configure Frame-Relay Switching?



Posted by: Sulaiman Syed
CCIE, Cisco, Configure, exam, how, Lab, map, router, switching

For some reason i thought that i have written an entry for Frame-Relay switching. But the records show none. So here it comes. During studies of CCIE, you might need to configure a Router to act as a frame-relay switch. The configurations are very simple and straight forward. There is the old...


Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to: