Networking Tag Directory

Featured Networking Questions

  • Configuring MS Exchange 2003 for SBS to send and receive mails on internet

    Hi, I have installed exchange server 2003 for SBS. I have configured it. Its working fine on LAN. I can send and receive mails from AD users. Now I want to send mails outside the network on internet. I have domain registered with godaddy (www.coinopsolutions.net). I have router working as DHCP...

    Kavinagpur10 pointsBadges:
  • Cisco 3550 config assistance needed

    Here is the network scenario: I have two T1's coming into our main building. One is a p2p T1 circuit to a remote office. The other is a basic T1 circuit for Internet connectivity. The far end of the p2p is in the 192.168.3.0 255.255.255.0 network. The local router is an Adtran with an IP of...

    Yernkie5 pointsBadges:
  • Cisco Router 2800 series step by step configuration using DSL

    Can you please provide me step by step configuration how to connect/use DSL connection for Cisco Router 2800 series. I want to use DSL as backup in case T1 is down.

    Erwin5 pointsBadges:
  • Router configuration is not saving in Cisco 2800 router

    I connect the 2800 to the configuration. Once the router is restarted router is going to ROM mode. The router configuration not saving.

    Venuchennu5 pointsBadges:
  • Cisco servers

    Hi, can anyone please tell me what they know about Cisco servers and their features please.

    Jboy5 pointsBadges:
  • comparaciones entre switch 2950 y un 3750 cisco

    necesito saber ventajas y desventajas de los switch cisco 2950 y 3750, ya que tengo que segmentar una red, ya tengo el 2950 pero esta la opcion de adquirir un 3750..┬┐que hago?

    Ald2030 pointsBadges:
  • Configuration of auxilary port for Cisco router

    Hi, we need to configure a adapter for third party. Our vendor need to login via PSTN through this router. I can configure the Cisco fax adopter but I don't know how vendor will login to this router Please explain. Can anybody describe what is the scenario "login through aux port via PSTN line"

    Ekansh400 pointsBadges:
  • How to configure load balancing on Cisco 1751 router with 2 serial WAN connections?

    How to configure load balancing on Cisco 1751 router with 2 serial WAN connections (different service providers)? Thank you.

    NetworkingATE1,545 pointsBadges:
  • Free Chapter – Cisco IOS XR Fundamentals

    Another free chapter download is available on the IT Bookworm Blog. Written by: Mobeen Tahir, Mark Ghattas, Dawit Birhanu, Syed Natif Nawaz Book: Cisco IOS XR Fundamentals Overview: "Cisco IOS XR Fundamentals is a systematic, authoritative guide to configuring routers with Cisco IOS XR, the...

    BrentSheets6,925 pointsBadges:
  • Designing a network

    A user recently asked this question via e-mail: I want to design a network, the specification is given below. Can you help me in this regard. Specification are 1) We have 7 site. 2) Each site have about 250 user and site one have 500 users 3) Exchange server, Mail server should be located at main...

    ITKE350,945 pointsBadges:
  • Cisco layer 3

    What command do we use for a layer 3 switch so it can also act as a router?

    Blangco5 pointsBadges:
  • Configuring IPv6 on 3825

    How do I configure IPv6 on a Cisco 3825 router, to route between two networks?

    Txstrat5 pointsBadges:
  • Cisco Encryption

    Is there a way to encrypt console port and vty port on a cisco switch/router using type 5 password encryption?

    Jd0085 pointsBadges:
  • Administration for Cisco UC500-series, resource recommendations

    I have recently found myself supporting a multi-site setup including a Cisco UC560, a 540, and a 520, and have been muddling my way through the administration so far. However, I am sure there is a wealth of knowledge that I am missing out on, and would like to fill in some gaps in my skill set. I...

    Zaltec15 pointsBadges:
  • Creating a bonded T1 for our data center

    We have two T1 connections coming into two cisco routers. The lines are from different providers. Can we make them into a bonded t1 for our data center? What equipment will we need and what configuration?

    NewnanIT1,110 pointsBadges:
  • Cisco Router 1841, will not Recongnise IP HTTP secure-server command

    I want to install SDM on my Cisco 1841 router, but the router will not recognize IP HTTP secure-server command, but I still manage to install the SDM on the router now I cannot configure the VPN because is not available i think due to wrong iOS release on the router.please how can I update it or...

    Olu15 pointsBadges:
  • Deploying VOIP and QOS

    We want to deploy VOIP to our network. We first need to implement QOS how can we do that? We have all HP switches and Cisco routers. The firewall is also a Cisco (PIX).

    Karl Gechlik9,860 pointsBadges:
  • Cisco 3825 Router

    Can cisco 3825 router support 45mbps link?

    Network Infrastructure5 pointsBadges:
  • Connecting two sites together with 3560G switch and 2911 routers

    I have 2 2911 series routers that I need to connect across a point-to-point T3 connection. Each router will connect to a 3560G series switch. One side the the Main site and the other side is a remote site. The connection right now is 3560Gs via T1, needing to upgrade for more bandwidth hence...

    pullthis5 pointsBadges:
  • Uploading IOS on Cisco 2110 series router

    How to upload iOS in Cisco 2110 series router?

    Camitr25 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following