IT Answers » WAP

Wireless Access Point

Barcagunner — Thu, 10 Mar 2011 04:07:34 +0000

My Organisation is looking for some software or a way to monitor our open wireless network. We have a few access points spread around the building and we woud like a method of tracking and keeping a record of IP addresses leased and associated Mac addresses for at least 10 days.

Any suggestions will be highly appreciated.

SonicWALL Sonicpoint-N 11A/B/G Dual-Band bundled with Poe injector

Srigoroso — Fri, 12 Nov 2010 18:45:29 +0000

Question Edited by Serena3

Cisco Access Point 1242 series

Ekansh — Fri, 09 Jul 2010 11:11:15 +0000

We have 21 Access Point in field in our company location. all are working and having the Good configuration along with channels and security authentication.

But now a days we are facing problem with 3 access points where wireless client in one vlan is not associating and there is no problem in other vlan.

when i see command show dot11 association

it gives following reply. so i am not able to see the ip address of the client due to this the associated client is not reachable from network. means the wireless client happend to be disconnected.

0017.2304.4467 0.0.0.0 4800-radio VMT-PM-131 self EAP-Assoc

wap application

Mlibra — Thu, 25 Mar 2010 23:57:17 +0000

how do i create a mobile/wap application??

the main function of the application would be unlimited sms to any destination..but i would like the application to have a center number (ie. people using the application simply use that center number to send receive texts so they do not have to connect to the internet to send receive sms) the outgoing/incoming sms should work on the same principle as mms

basically people using the service would be connecting to a third party private wimax network in another part of the world

also how do i create and manage a billing system for such a system? as i will have to pay the third party provider for hosting my application??

Level 1 WAP 1001 Outdoor units

FintanM — Thu, 25 Feb 2010 07:59:01 +0000

I have a situation where i have linked two warehouses with separate level 1 WAP 1001 outdoor units. one acting as an access point and the other as a client. The client is connected to a dlink switch that then feeds two dumb terminals and CCTV DVR. The Access Point is connected to another DLink switch that distributes the WIMAX signal that connects the warehouses to the HQ.

My problem is that the client unit keeps losing connection to the access point at various intervals. most of the time the connection is stable but it becomes eratic every so often.

I have tried the following:

1 . Re-terminated the connections

2. Reposition the Outdoor units

3 Run a new STP cable to the Outdoor units

4 Changed the channel to automatic selection for the two units.

I am not very sure what to check for next, but i i am suspecting external interference. Could there be any other explanation and solution to this problem?

How to redirect WWW to WAP

Arthurmasons — Fri, 16 Oct 2009 19:54:22 +0000

Hi, would anybody help to understand of how to redirect www site to WAP site when navigating via mobile internet connection

connecting wireless PC to a wired network with internet

Iecep1 — Mon, 06 Oct 2008 11:44:27 +0000

how to connect a desktop PC to an internet connection 25meters away from a laptop connected(wired) on a DSL(internet) modem?

Access Point issues netgear WG302 Access point

MK10000 — Tue, 23 Sep 2008 16:26:34 +0000

I have a netgear WG302 Access point that is giving me a headache. I can configue it and it will work fine, until my isp changes the ip address. Then I have to reconfigue it again. I have tried static routing options through the router hoping this would fix the problem. no luck. (It may have been that the access point was connected to the switch instead of the router like it is now – I have not had the time to troubleshoot this yet)

I also have the option of selecting DHCP in the access point setup, but dont know how to configure it properly and it locks up ( i think because I am trying to use similar ip/subnet info as my router.)

I think I’m close to fixing this problem, just hoping someone can clarify for me.

I do not have a static ip address from the isp.

Thanks for the help!

Changing Duplex on a POE Cisco 1231 WAP

Flame — Wed, 10 Sep 2008 13:50:02 +0000

On a network I am working on I have a Cisco 1231 WAP that is powered via POE. The Duplex is currently set as “Half”, while the rest of the WIFI network (3 more 1230 series WAPs) is set as “Full”. This is causing the device to throw an error once per second. All the WAPS, including the half duplex 1231 are working, but it is making for useless error logs, as important notices tend to “scroll off” the log file before I can get to them. If I want to change Duplex on the device, I get a warning that since I am using POE, there could be problems during the necessary reboot to set the device to full duplex. I could power the device via a regular wall wart and reset it that way, but the problem is getting to it. It is installed high up on a wall, above a large press, the maintenance guy said it would take most of an afternoon to get to it using a man lift My question is this, has anybody ever reset the duplex on one of these while using POE? While I’m thinking I’m going to be spending some quality time high above the ground soon, I’d like to avoid shutting down a press and jumping though all the other hoops to get at the WAP if I don’t have to.

Thanks!

AP-5131 WAP RADIUS Configuration?

erin0201 — Tue, 29 Jul 2008 16:22:53 +0000

New Discussion Post by