What are virtual lans or vlans? What are they used for and will they allow me to increase my networks overall speed and throughput ratio?
Is there a network monitoring tool to alert me to when my network becomes too saturated and recommend what to do like spit more subnets or set up vlans? How can I view collisions and the such?
How do you implement Active directory with VLAN
We have collapsed backbone haireicheal model in our network. All interface vlan routing and l3 configuration is done on core switches itself. But i want to know that If i have core-distribution-access layer model then vlan routing should be done in distribution layer so what should i have to configure on core layer?
Port assigned for vlan1 is 1 to 25, port assigned for vlan2 is 26. I could ping gateway or browse internet from vlan1. But from vlan2 I can not ping or browse.
can you please provide me a comparison between HP Procurve switches and Cisco Switches in these points : ports,VLANs,link aggregation ,spanning tree,PoE,VoIP,DHCP,routing using OSPF
Hello All, I have a cisco Cat 3560G switch trunked to a 3com 4200 L2 switch. I have 4 Vlans created on the Cisco L3 switch like Vlan 10, 20, 30 and 40 and created only 20 and 30 on the 3 COM. All the trunk port configurations are fine. However when i assign a [...]
I need help adding an IP subnet to a Vlan, when I attempt to by using the IP address X.X.X.X 255.255… it gives me an error saying it overlaps another VLAN. is there another way to do this? I am on a 3750 cisco switch, IP routing is turned on. Please help!!! thanks in advance.
[u3:p][/u3:p] Create vlans Add ports to vlans Set port 1 as trunk and also added as tagged to all vlans At port 1 i connect my adsl modem router (dhcp enabled). 4500 switch gets 192.168.1.100 as it’s ip but all other computers can’t get their ip by the dhcp if they are connected via 4500 [...]
Hi all, 1 .How to configure DHCP assign ip to different subnet? 2. How to configure DHCP Server? 3. How to configure CISCO 3560 become DHCP relay agent? Hardware: DHCP Server is installed on Server 1 (Windows 2008 R2) TMG2010 is installed on Server 2 (Windows 2008 R2) Cisco 3560 Switch DHCP Server: Native VLAN [...]
I don’t know for sure how to ask for it, so I’ll explain it to you first:[Br style=”padding: 0px; margin: 0px;” />[Br style=”padding: 0px; margin: 0px;” />- I currently have a Linksys SRW224G4 switch, in which I have connected 10 servers. [Br style=”padding: 0px; margin: 0px;” />- From those, 9 servers are ours, and the other one is [...]
Hi everyone, Im setting this up for a church and well stright to the point….. I am trying to set up 2 SSID’s on the AP both on diffrent VLANS I have a cisco 1700 router connected to the switch(FS726T) and have VLANs configured already on both the router and switch. (They work) On the [...]
I have a T1 from my telephone provider. I also am installing Cable internet. I need to point my Administration vlan to the cable and my student vlan to the T1. But my Verticle voip phone system runs a phone management app that needs to stay on the Administration vlan and point to the T1. My [...]
how many vlans for telepresence switch 3750? I did data vlan,video vlan, voice vlan and management vlan. am I still left any vlans? by the way, what book is good for telepresence configuration?
would different vlans have different subnets?
Hi Can any one please explan me about Vocie Vlan.
We have an Alcatel Core switch connecting several VLANS togethers. Everything is running fine as we desire, except for the following problem. If I run the trace route (tracert) from a computer to another and these two computers are on the same subnet and connected to the same switch module, in some cases I get [...]
We have an Alcatel Core switch connecting several VLANS togethers. Everything is running fine as we desire, except for the following problem. If I run the trace route (tracert) from a computer to another and these two computers are on the same subnet and connected to the same switch module, in some cases I get [...]
Hello, I have 2 switches – one in building X and the other in building Y. The buildings are connected via fiber and eigrp is the protocol that’s setup between them. The buildings are p2p connections between 7200′s. I need the Vlans to be propagated from switch “y” to switch “x” over the L3 connection. [...]
Window 7 machines are picking IP on only some vlans. I suspected the issue might be trunking and checked. But strange to see trunking configuration are same… Please suggest.





