• New 2003 install on the domain can’t see the network

    Long story short, a windows 2003 system died with a bad hard drive. Hard drive has been replaced and I am installing a fresh windows 2003 onto the system. Everything is updated and it joins the domain fine. The problem is I cannot see any other systems on our domain. I can do a \stampy from my...

    Kevins740 pointsBadges:
  • Change Telnet port in Linux (Debian)

    Hello everybody. I'm not a Linux expert, and am looking for a way to securely communicate with a Linux machine via Telnet. To avoid sending user and pwd without encryption I'm going to open a ssh tunnel (with putty or plink) forwarding port 22 (ssh) on the linux machine to another port, in which...

    carlosdl69,410 pointsBadges:
  • Unable to detect a parity error with Windows SDK on a PCI serial card

    We are using a 9-bit protocol which sometimes sends a mark state and sometimes sends a space stage. When a space state is sent we want to be able to get a parity error in SDK. We can see the parity error in the hardware register but we want to be able to see the error with Windows SDK software....

    Kfink040 pointsBadges:
  • Network Resource Allocation cum Planning cum Technical Problem

    This is the real commercial problem face by my company. Well, the reason I ask this problem is I salute and respect all of you as I believe all of you are as good as network solution company out there, or even better!! Lets me rephrase the entire problem again. Company expand so fast that the IT...

    Hunkgym5 pointsBadges:
  • Design NEW network cum NEW IT infrastructure-2

    Company expand so fast that the IT infrastructure is not fast enough to cater high volume of traffic; the initial design is not scalable. The number of new branch offices setup caused the company pay a high price in the leased line communication. Salesman and management staffs dial into company...

    Hunkgym5 pointsBadges:
  • Communication between 2 AS/400s

    We have the Softlanding product Turnover to do our change management. Our development machine is in a different building and we distribute our software using that tool via FTP. From development to production machine we use a VPN tunnel (note this is controlled by network people). The software uses...

    Senator460580 pointsBadges:
  • keepalive

    HI, I am preparing for the ccna exam. Can any body help me, what is the purpose of keepalive command which we will give in routers when configurin the physical interfaces. Thanks & Regards, Rajesh.M

    Mraj270 pointsBadges:
  • Domino Server & VPN

    Hello, I have this problem: environment: 2 Domino 6.5.1 in Head Office (one for mail, the other for applications), a Domino 5.0.7a in remote office (in a different country). The connection to this country is based on VPN over internet; problems: 1)sometime the home router "hangs" and the mail was...

    Mauriz140 pointsBadges:
  • bgp inbound filter

    Does anyone have any experience configuring BGP filters? If so, here is my dilemma: One of our core routers is hooked up to ISP A via BGPv4 and is recieving the full routing table of which is in excess of 100,000 networks. I would like to have it recieve routes only from ISP A's AS, and NOT every...

    Ligmania0 pointsBadges:
  • Access point/router

    I would really like to know the detailed difference between a router and an access point. Do I need access points if i am going to set up a network and have two routers already? How can i use a router as an access point if that's possible? Please explain. Thanks

    Frenyb0 pointsBadges:
  • How can I route ip1:port1 to ip2:port2 within windows

    Hi, are there any standard tools in windows to setup a route from ip1:port1 to ip2:port2? So if I call ip1:port1 I end up calling ip2:port2. I looked at netsh and found something that could be the solution (portmapping under routing - ip - nat), but can't figure out how to setup the whole thing....

    Chilkman0 pointsBadges:
  • Servers preventing NEW connections from remote clients

    Hey all, I have an interesting problem and hope that someone can help resolve it. At the minimum, I have to reboot one or more of my servers at the main site because all of my remote users located across a direct T1/VPN tunnel can no longer get connections to the server with the exception of being...

    Swiftd0 pointsBadges:
  • Domain Admin Group

    Does anybody know of a way to search our Active Directory to see what users are part of the Domain Admins Group. If so, what software and where do I get it. Thanks

    Vman660 pointsBadges:
  • Accesing Network resources on a WLAN

    I created a small office network between five computers (a WLAN actually), four of which I installed from scratch. The fifth, which I didn't install the OS (Windows XP) myself, can be seen in the workgroup under Microsoft Windows Networks form other computer, but an attempt to access it fails, with...

    Lance010 pointsBadges:
  • Postfix and DNS

    I have installed Postfix on my server with DNS. I am not sure what information I should provide here so let me explain the setup and goals. I have SuSE Enterprise 9, Apache, Static IP address. In other words a hosted website/server. The goal is to also have this as a mail server. I am able to send...

    Sapient0 pointsBadges:
  • Loadsharing between two ISPs

    dear sir, I am looking for a load sharing solution between 2 leased lines for 2 different ISPs the diagram goes lke this: LAN-->Cisco Pix-->Router-->2 leased lines. can load-sharing be done at the router without extra configuration at the providers side? can CEF (cisco express forwarding)...

    SkullyMJ0 pointsBadges:
  • Remote Syslog with MySQL and PHP

    Dear All, i want to set up a Remote Syslog with MySQL and PHP on system with whitebox linux,can some tell me a step by step on how to install and configure this,also the requirement needed to complete the task Regards Edwin

    Eduado0 pointsBadges:
  • Optimizing printing and imaging environment

    how can i Optimize printing and imaging environment

    Eduado0 pointsBadges:
  • Re: Windows Time server

    Hi All, Let me give an overview of our forest: We are on a Windows 2000 mixed mode forest. We have 2 Dc's in my parent domain and a standalone ntp server not on our domain but within our network segment which goes out to get time from Microsoft time server. On PDC emulator we set this sntp server...

    Shabuitty0 pointsBadges:
  • Setting Up VLAN across WAN link for Testing

    I am trying to setup a Vlan via a WAN Link. Local End has already 4 VLANs. Remote End doesn't. Remote end needs to access VLAN id 4 via the WAN link. Local Gateway router = Cisco 3660 Remote Gateway Router = Cisco 3660 Local Switch = Cisco 3750 Remote Switch = Cisco 2924 What is the config that...

    Aparian0 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following