• Procedures for a new area.

    We are a company where we have expirience on network remote administration and now we have open a new area, The area of security. Now I need to start to make new procedures like when a new customer come to us and ask if we can handle the security for his network... I need to know if some one can...

    Millan0 pointsBadges:
  • Static Routes

    We have a remote location comunicated with our headquarters by antennas, using 2 vlans, one for the data and one for the voice. We recently adquiring an E1 with our ISP and need to split up the traffic in order to balance charges. We have a 2801 Cisco router in the remote site and a Catalyst 500...

    Jortizga10 pointsBadges:
  • How do I route from the switch interface to the last machine?

    If an interface of a Layer 3 switch is configured for network "A," and three computers have connected in a serial manner to that port (what I mean is in a line) how do I route from the switch interface to the last machine?

    NetworkingATE1,545 pointsBadges:
  • What’s broadcasting and which switch will fix timed-out requests?

    I am an Internet distributor of Exatt.net. When my customer pings the gateway it gives me lots of timed-out requests. Exatt.net says it broadcasts in your network. What does this mean, and how can I fix my timed-out requests? I use a hub. Someone told me to use a management switch, but I have no...

    NetworkingATE1,545 pointsBadges:
  • CISCO commands

    What CISCO command would you use to see devices connected to a switch\router?

    Rmatt5 pointsBadges:
  • STATIC IP ADDRESS REQUIRE WITHIN A CISCO 4006 SWITCH USING VLAN

    Hi Guys, I have a VLAN configured on a Cisco 4006 switch port, I have already create VLAN 210 on the switch, and assign some of the interface to that VLAN 210, now there is requirement that I need to provide some static ip addresses to couple of devices Now my problem is that I know that I need to...

    Gbollyd5 pointsBadges:
  • One Way Ping

    Hi All I have a point to point wireless link configured in routing mode with Network end connected through a switch to firewall. IP's are configured as follows: Ethernet IP: 10.1.1.99 Wireless IP: 10.0.0.10 G/W : 10.1.1.1 firewall The subscriber (remote end) Ethernet IP: 172.16.1.150 Wireless IP:...

    Wex Mark5 pointsBadges:
  • Can you connect a Cisco 7940 desktop IP phone through a wireless switch/bridge to a Cisco access point?

    Is it possible to connect a Cisco 7940 desktop IP phone through a wireless switch or bridge to a Cisco access point (AP) and make it work? I am having problems with this setup. It is most probably unsupported but we sure would like to make it work. Thanks!

    NetworkingATE1,545 pointsBadges:
  • Installation and updates

    Howdy folks, Tryin to keep things going around here....need some advice. I have Win2003 servers and Active Directory.....single domain....approx. 100 client computers.....one location. Am upgrading all computers from Office XP to Office 2003. My project: Install Office 2003 and all updates remotely...

    TheVyrys0 pointsBadges:
  • Recommendation for Switch that can do MAC Address based VLANS?

    I'm looking for implement MAC address based VLANS in my network, does anyone have any recommendations for a switch? I was hoping to keep it under $1000. Thanks!

    Billb320 pointsBadges:
  • Need help designing a network for videoconferencing for a campus?

    What type of severs, routers, bridges, switches and cables are suitable for videoconferencing? Also, how do you design a network for videoconferencing for a campus? Please help me. Thank you.

    Networking Channel ATE30 pointsBadges:
  • What type of network gigabit switch

    We are a small office and currently have a Dell Power Connect 2124 24 port switch. I would like to upgrade to a 48 port switched seif managed.. Would the Dell PC 2748 suit our needs? Or can I use what we have and only route the PCs and laptops to the new giga switch?

    Caddman35 pointsBadges:
  • Network timeouts

    We've been having occasional network timeout issues with a particular group of users on a very old 10/100 switch. So we upgraded their switch yesterday to a brand new Gig switch with larger throughput capacity. (Have not upgraded the users to Gig NICs yet.) Anyway - It made the problem worse! They...

    Dilbertina35 pointsBadges:
  • NTP configuration on the layer 3 switch

    hi i have 3750 switch in my practice lab i want to configure NTP on the same as well i want to sync. the remaning l2 switches with that ntp timinings.

    Network Info5 pointsBadges:
  • Network setup

    Our organization has been using a small office network and would like to expand it to cater for the increasing organization needs. We have therefore upgraded our Internet connection to a DSL with 15 IP addresses and purchased high end servers to manage a network of an estimated 150 computers. I was...

    Wanaug5 pointsBadges:
  • amber lights on 3gb mcdata switch

    suddenly and inexplicably I've got switch port amber lights on a 4gb 24-port mcdata switch; do I need to swap the switch or perform a firmware upgrade?

    Luciusm01245 pointsBadges:
  • how to prevent Collision in my network

    my user sometimes they can't open the data file mapping . but need to log out and login again when they did this they can open the file server. i have 3 switch dell 4 3com all of them are 24 ports i have 1 hub that series the 3 switch, pls answer me cz , iam new here this company.

    Sirduz135 pointsBadges:
  • Test cases for Ethernet switches

    I'm working on a project which is on the Ethernet switch. I'm totally new to it. Could you help me with access control lists (ACL), Quality of Service (QoS), and packet filtering concepts in detail? I find it difficult writing test cases for it.

    NetworkingATE1,545 pointsBadges:
  • Configuring a Netgear Layer 3 switch as a router

    I just bought a Netgear Layer 3 GSM7324 Switch. We are paying for collocation services at a Datacenter. We need to configure this switch as a router since we are going to connect servers with public IP's direclty to the switch. We contracted a 1Gbps port and the collocation facility is providing...

    Mlev113011300 pointsBadges:
  • Upgrading network switch to 1000 mbps

    Currently, I have 48 ports used on a 10/100 switch on network. I would like to upgrade my switches to 10/1000. Will this effect how my infostructure is setup? Interms of wires and jacks on the wall. I do understand that my ethernet cards must be capable of 1000 mbps. We are upgrading all the...

    OMAR50 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following