• How to create VLAN with this Cisco configuration

    Dear Sir, I have 1) DNS & Exchng Server 2003 with DHCP enabled Win2003 Standard Edtn SP2 , 2) ISA 2006 3) Trend Micro Antivirus Server. I have to create VLAN for 3 Dept. with having 3750 Cisco Switch as routing ( Trunk ) Using 2950 Cisco Switch 2950 VLAN10 High management VLAN11Low management...

    Abduljaleel5 pointsBadges:
  • Cisco Catalyst WS-C6506 – link termination question

    I need Help for one of our solution on our site. Senario We have a simple campus network on our site where we have Core, dist.and access Switches. Two Core Switches that are C6506 having redundancy. CAT6507 Chasis WS-C6506 SUP WS-X6K-SUP1A-2GE MSFC-2 WS-F6K-MSFC2 1000BaseX Ethernet WS-X6416-GBIC We...

    Chitah10 pointsBadges:
  • Connecting data closet switches to the core with redundant links

    I'm moving our flat network which covers a three-story building and about 450 users to a subnetted network. I would like to know about connecting data closet switches to the core with redundant links. Can I implement OSPF on the core and connecting switches and eliminate spanning tree? In this...

    NetworkingATE1,545 pointsBadges:
  • How to put Access Control List in Cisco WS-C2960-24TT-L

    What are the commands to put Access control List in cisco WS - C2960-24TTL

    Whyshree5 pointsBadges:
  • Fiber Ports on Cisco 2950 24 port switch

    I have fiber connected to my 2950 but it does not work. I did a light test with the fiber strands and they are good. Is there anything else tyhat I am missing that must be done.

    Livesquad5 pointsBadges:
  • Performance of Cisco 3750 Layer 3 switch

    Hi guys, I have a cisco 3750 series L3 switch. It can currently handle 3GB of L2 traffic with no problem, but when faced with 40MB of L3 traffic, CPU utilization shot so high that I can't even telnet to the switch. Could anyone enlighten me please? Thanks in advance!!

    Bluezerk15 pointsBadges:
  • How can i configure a port for multiple vlan at Netgear FS728TS (like “trunk port” at cisco switch)

    i have an Netgear FS728TS switch and i have to use 2 vlan with an cisco switch. (i have no problem about cisco switch configuration) vlan name=Default vlan ID=1 vlan name=AP vlan ID=307 there is F/O cable connection between two switches. 1/g1 port using for this F/O connection at Netgear switch. in...

    Myselfziro5 pointsBadges:
  • VLAN setup and configuration

    We have 2 switches with different ip range say 10.1.10.0 and 10.1.15.0.I want to connect both the switches with same vlan say vlan 4 so that they can communicate.switch 1 should be valn 2 and vlan 4 but switch 2 should be vlan 4.

    Philip315 pointsBadges:
  • telnet feature in Netgear Smart Switches

    I have a handful of netgear FS726TP and FS728TP switches deployed in this organization. The FS728's have a MAC address and IP table feature, but I cannot find the same functionality in the FS726s. I want to telnet into the device from CMD, but I am receiving the normal error: "Could not open...

    Schmidtw11,330 pointsBadges:
  • How to identify the users in the network

    I am working on my Masters Project in which I am supposed to design a Network Monitoring tool which will identify the users in the network based on their network behavior. I have a network setup with 4 systems connected to a Switch --> Router --> Internet. I connected another system to the...

    Sindhukakuru30 pointsBadges:
  • What does a switch do with a frame addressed to a MAC address that is not in its MAC address table?

    What does a switch do with a frame addressed to a MAC address that is not in its MAC address table?

    Hotti4sho5 pointsBadges:
  • On a Cisco Catalyst 6500, both supervisor cards in hybrid mode sync up automatically in terms of both operating system and configuration

    On a Cisco Catalyst 6500, both supervisor cards in hybrid mode sync up automatically in terms of both operating system and configuration

    Looses10 pointsBadges:
  • Cisco Catalyst Express 520 Switch Console?

    I have just taken delivery of a the above mentioned switch. It doesnt have a console port, does anyone have any idea how to access the IOS?

    BlackBullet30 pointsBadges:
  • multiple lans, subnets, dsl connections on the same cables

    well this is my first post and its a doosie. At lewast for me. Looking for an all wise network guru!! =] we had an existing network consisting of 10pc's, a win2k server and a dsl connection. all was fine... dsl router:192.168.0.1 server: 192.168.0.10, 192.168.0.50 easy as pie... now we are partners...

    Jabooma15 pointsBadges:
  • Configuring Qtrunk ports on FS728TS Switch

    I need to connect two switch FS728TS. I have 3 Vlan in each switch. How can I configure the common ports of every switch to achieve the 6 Vlans traffic flow on this link

    Tecuntecun5 pointsBadges:
  • Network Controller Driver missing, company not known

    Hi, All of a sudden my working network controller's driver went missing. I have dual boot (XP, ME), and it is missing in both OS. Could it be a hardware problem ? Do I need to replace the network card ? I searched for the driver in WinXP installation disc, but didn't find it, though WinXP had...

    Akash2160 pointsBadges:
  • Securing against rogue DHCP servers

    Looking for an example of how to configure Cisco DHCP snooping. Can someone provide example settings - or point me in the right direction? Many thanks. Moderator Note: This is a user submitted question

    BrentSheets6,925 pointsBadges:
  • Will having a router between each switch improve performance?

    Will having a router between each switch improve performance on a network?

    A1sysnet5 pointsBadges:
  • Multiple public IP’s from 1 internet connection on different networks?

    Is this a possible scenario? A cable modem is hooked up via ethernet to a Linksys 5-port switch. That switch is then hooked to a Cisco SOHO router (not managed by me) and my Linksys router. I cannot get my public IP to work on my router but the Cisco routers public ip comes up fine. I have all of...

    GatekeeperJB45 pointsBadges:
  • How to rate limit on Cisco Catalyst 3550-EMI

    Hello, I have a cisco switch 3550 EMI and I need to do rate limiting on ethernet ports. class-map match-all 5M description 5M with 500K burst ! policy-map 5M class 5M police 5120000 51200 exceed-action drop interface FastEthernet0/3 switchport access vlan 100 switchport mode dynamic desirable speed...

    SupermanInNY5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following