• Layer 2/3 switches

    When I am trying to put the default gateway in layer 2 switches with IP default-gateway xxxxx command it okay. But If I'm trying to put the default-gateway in 3560(layer 3) switches with IP default-gateway xxxxxxx command its giving me error that invalid command.

    Jadu50 pointsBadges:
  • Remote Desktop Connect

    How to I setup a RDC connection for DLink switch?

    So155 pointsBadges:
  • Free Chapter – Implementing Multicast on Cisco Catalyst Switches

    Another free chapter download is available on the IT Bookworm Blog. Written by: David Barnes and Basir Sakandar Book: Cisco LAN Switching Fundamentals Overview: "Cisco LAN Switching Fundamentals provides an easy-to-understand introduction to LAN switching best practices using Cisco Catalyst...

    BrentSheets6,925 pointsBadges:
  • Connecting data closet switches to the core with redundant links

    I'm moving our flat network which covers a three-story building and about 450 users to a subnetted network. I would like to know about connecting data closet switches to the core with redundant links. Can I implement OSPF on the core and connecting switches and eliminate spanning tree? In this...

    NetworkingATE1,545 pointsBadges:
  • Setting up switches and VLANs

    I am going to an interview that requires me to set up 3 switches, VLANs and do some routing. Do you have any ideas what that might entail?

    pslang10 pointsBadges:
  • Configuring Qtrunk ports on FS728TS Switch

    I need to connect two switch FS728TS. I have 3 VLAN in each switch. How can I configure the common ports of every switch to achieve the 6 VLANs traffic flow on this link?

    Tecuntecun5 pointsBadges:
  • Cisco Switch 3560 assigning IP address manually

    I have a Cisco 3560 Switch. How should I define the IP address and subnet mast through telnet? I cannot access express set up mode. I want to assign the IP address and subnet mask manually through telnet. Please help me. Thanks!

    Rabbanimd5 pointsBadges:
  • Anyone know of a free simulator for Cisco router and switch configuration?

    Can anyone recommend or suggest a free simulator for Cisco router and switch configuration? Thank you!

    NetworkingATE1,545 pointsBadges:
  • How to install 2 virtual client with Windows 2003 Server

    Hi, I would like to know how to install 2 virtual client with Windows 2003 server? Do we need a KVM switch with additional configuration and license?

    Retrohydra5 pointsBadges:
  • 2IPS’s, 2 routers (1 router per each ISP) connected 8 workstations through 2 L1-switches – will this work?

    2 IPS's, 2 routers (1 router per each ISP, diferent LAN-subnet on each router) connected to 8 workstations (through 2 L1-switches) - will this work? (it does actually work but with disruptions)? 2 ISPs are required in case one IPS's connection is down. Thequestion is will the other ISP's connection...

    Eager2knowlan35 pointsBadges:
  • Is there any method with which one can increase the port speed or bandwidth for a particular port of a switch

    Is there any method with which one can increase the port speed or bandwidth for a particular port of a switch (2950 or 3750)?

    NetworkingATE1,545 pointsBadges:
  • Career change: programming to networking

    I'm looking to move from programming to network administration and eventually security. I need advice. I have an AA degree. I did tech support and programming part-time in college. Since then, I've spent 2.5 years as a programmer (with some IDS responsibilities), 1.5 years doing QA on niche-market...

    Unicityd30 pointsBadges:
  • Pretty strange problem in my network

    Hi Everyone, I have a client who has 10 computers . He also have 10 ADSL connections for internet connectivity (all from single ISP). We want to setup the environment in the following way: we have 2 D-Link simple switches with 24 ports. What we wanted to do is to connect all ADSL modems to one...

    Aligator0075 pointsBadges:
  • Configuring a Foundry Switch

    I am not a Network Specialist, but I do know a small amount about configuring a CISCO switch. However, I have been asked to configure a Foundry Switch. I am having problems with a few commands and maybe someone out there can help me out. Here is what I'm getting when I try and configure this...

    Louann5 pointsBadges:
  • What’s the difference between hub, router and switch

    What is the difference? How do you know which one to use? Thanks.

    OverDraw10 pointsBadges:
  • How do network hardware devices support IPv6?

    I read that most routers and switches support IPv6, but how they support the protocol differs. The article said that specific network hardware devices have dedicated network processors while others have general purpose processors, which are worse because those forward packets at a slower rate. How...

    SearchEnterpriseWAN1,080 pointsBadges:
  • Getting it all to work together – Network design

    l am setting up a very basic network but still need to be reassured, my network consists of all the following which should all be used: 6 computers 24 port switch 24 port pathcpanel router modem one storage rack The only piece that has put me off is the patch panel as l honestly and embarrassingly...

    clivaldo10 pointsBadges:
  • How should I upgrade my network infrastructure?

    I am now upgrading the network infrastructure of my office and I have 10-15 computers. Now what I want to do is to connect to the Internet with a wireless or wired Ethernet connection and connect the Microsoft workgroup sharing with another wired Ethernet. Is it possible to connect a LAN connection...

    NetworkingATE1,545 pointsBadges:
  • finding fault of Network Ping drop

    I am having a bus topology network with OFC connected on ABCDEFGH switches. OFC SM link is followed from A to B to C to D to E to F to G to H to A one side and A to E with redudence line. When we ping all the switches one by one, there is no ping loss. But when all the swtiches are on, I find ping...

    Pgreddy15 pointsBadges:
  • Trying to replace old 10-Base t hubs with new technology routers and switches

    There are 200 computers in my office. Which communication mechanism should I use and what type of routers and switches should I use?

    Harjot5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following