Switch Configuration

installing a new switch

What all needs to be done when upgrading and adding new switches where old ones exist Software/Hardware used: windows Xp

Username&password

hi, i'm trying to configure username$password on the PC6224P. i use the command: "username....pass....level 15 encrypted." it saves the configuration but won't use the limittation when i login. what should i do?

vlan setup

I have a 48 port linksys/cisco switch that i want to split between two subnets, .0 and .9. How can i setup a vlan to distinguish between two or if i wan to setup 3 different subnet. I am new to this, any help with some examples as to how to setup would be greatly appreciated

finding fault of Network Ping drop

I am having a bus topology network with OFC connected on ABCDEFGH switches. OFC SM link is followed from A to B to C to D to E to F to G to H to A one side and A to E with redudence line. When we ping all the switches one by one, there is no ping loss. But when all the swtiches are on, I find...

How to configure inter vlan routing on a router, vlans on two cisco switches, creating a trunk between two cisco switches attached to a router on each

I have a scheme of two switches connected to each other, three routers, one router is connected to a switch and two routers are connected two another switch. How I'm i supposed to configure vlanX, vlanY on two different switches and trunking between them, inter.vlan routing on a router and trunking...

problem encountered between 3com 4950 to catalyst 500

I encountered a problem between the connection of 3 com (4950) to catalyst express 500. 3 com is located in the server room and act as our distribution switch, from server room it is connected to catalyst 500 using fiber optic cable (multi mode). I connect the 3 com to the sfp uplink of the...

Port monitoring with HP ProCurve 4104GL

Having problems configuring a Web filter with a HP ProCurve 4104GL switch. Does this switch support port monitoring? Thanks. Moderator Note: This is a submitted question

Configuration between L3 switch 3750 and L2 switch 2960 via trunk port

I am going to connect three L2 switches 2960 from L3 Switch 3750, means all three L2 switches are connected to L3 switch via trunk switch. Thanks & Regards, And i am going to configure VLANs on L3 Switch. So plz let me suggest,if both switches are in server mode then i should configure VLAN on L3...

VLAN Routing

We have created two VLANs on single Cisco C3560 switch and now want to have inter-VLAN routing. Please explain how to enable it. Please note, we have only one L3 switch, with 10 computers on one VLAN and 10 on other VLAN.

Cisco Catalyst WS-C6506 - link termination question

I need Help for one of our solution on our site. Senario We have a simple campus network on our site where we have Core, dist.and access Switches. Two Core Switches that are C6506 having redundancy. CAT6507 Chasis WS-C6506 SUP WS-X6K-SUP1A-2GE MSFC-2 WS-F6K-MSFC2 1000BaseX Ethernet...

How to create VLAN with this Cisco configuration

Dear Sir, I have 1) DNS & Exchng Server 2003 with DHCP enabled Win2003 Standard Edtn SP2 , 2) ISA 2006 3) Trend Micro Antivirus Server. I have to create VLAN for 3 Dept. with having 3750 Cisco Switch as routing ( Trunk ) Using 2950...

How to put Access Control List in Cisco WS-C2960-24TT-L

What are the commands to put Access control List in cisco WS - C2960-24TTL

Configuring trunk port in Dell PowerConnect 6248

when i configured trunk port in dell 6248 switch, it gets hangs. what the issue. also it won't allow vlan-1 traffic to pass through. Pls. suggest what to do??

Bind IP subnet to VLAN in Dell L3 switch

when I bind an IP subnet to dell 6224 switch, does it mean when i plug in a pc within tat particular subnet will directly be in that VLAN? Example: i type in "vlan association subnet 10.0.1.0 255.255.255.0 10" to bind subnet 10.0.1.0 to VLAN 10. so is it when i plug in a PC with IP 10.0.1.30 into...

How to restore the start-up configuration of a Cisco switch

I have a 2950 Cisco switch, the command that I used is "erase startup-config". After using this command I reloaded the switch and when it asked me to save the changes I said yes. Now whenever I use the switch it does not take me to the user prompt anymore but in fact all I get is switch: I think...

VLAN setup and configuration

We have 2 switches with different ip range say 10.1.10.0 and 10.1.15.0.I want to connect both the switches with same vlan say vlan 4 so that they can communicate.switch 1 should be valn 2 and vlan 4 but switch 2 should be vlan 4.

Port security for Switches

Switch(config)#interface fastEthernet 0/1 Switch(config-if)#switchport port-security Command rejected: FastEthernet0/1 is a dynamic port. why is that happening

Securing against rogue DHCP servers

Looking for an example of how to configure Cisco DHCP snooping. Can someone provide example settings - or point me in the right direction? Many thanks. Moderator Note: This is a user submitted question

Setting up Cisco 2950 switch

Hello, New to itknowledge exchange... I have a hand me down Cisco 2950 12 port switch. I currently have assigned to my Cable Modem4 Static Public IP's Note: Not real but used for example. 70.66.131.1 70.66.131.2 70.66.131.3 70.66.131.4 I run 3 servers in my basement all of which I have...

Performance of Cisco 3750 Layer 3 switch

Hi guys, I have a cisco 3750 series L3 switch. It can currently handle 3GB of L2 traffic with no problem, but when faced with 40MB of L3 traffic, CPU utilization shot so high that I can't even telnet to the switch. Could anyone enlighten me please? Thanks in advance!!