• Routing Between Two Networks

    1.I have two separe networks 192.168.1.0/24 with a Juniper Netscreen NS5GT and the second network is 192.168.5.0/24 with a Netgear WNB2100 Router ,they r physicall connected by CAT5 cable though the Internet port. I can ping from the 192.168.5.0/24 to 192.168.1.0/24, but i can't ping the other way....

    Datamatt15 pointsBadges:
  • Route map Cisco

    I have a cisco router 1841. It has 2 outside adsl interfaces, and an inside interface connected to local lan. I want to use the 1st adsl interface for http, ftp and the 2nd adsl interface for the rest of the internet traffic. Below is a sample of my configuration: interface FastEthernet0/0  ip...

    Meglo161020 pointsBadges:
  • Why can’t I connect to the Internet through my new GBIC module?

    On the MDF Rack is a Linksys switch that has 24 ports with two mini gigabit interface converter (GBIC) modules: One GBIC module port states up to 12; the other port states up to 24. [o:p][/o:p] Also, there are two fiber patch panels with 12-pair wires connected to Ports 1-2 3-4 5-6 7-8 9-10 11-12...

    NetworkingATE1,545 pointsBadges:
  • TWO DIFFERENT IP ADDRESS

     Port Forwarding Port Checker  give's me this ip address"192.168.0.184". But Open Port Check Tool return this ip address "24.247.163.127".      What I try to do is set up an COD4 server, but unable to open the correct port " 28960". I am using an D-link DGL 4500 router.

    Josephsuun5 pointsBadges:
  • Cheap, Good and Easy way to rout and load balance a second Internet uplink

    We would like to add a second Internet line into our school. I'm looking for an easy solution, because I have very limited knowledge of networking. It needs to be inexpensive, because we are on a show string budget (like everyone else right now except the banks). And it needs to do a good job of...

    Techobi25 pointsBadges:
  • Is there a way to edit my firewall rules in one place?

    Can I configure my network to reroute traffic to one server, so I can edit my firewall rules in one place?

    NetworkingATE1,545 pointsBadges:
  • Can’t connect D-Link media converter with Cisco switch 2950

    I am using Cisco switch 2950 connected with a D-Link media converter. When power is reset, that switch is up but the port connected with the media converter is down. After I reset power of the media converter, the link comes up. What's going on here, and how can I fix this?

    NetworkingATE1,545 pointsBadges:
  • 2 DSLs aggregated to a Cisco 5505 asa router

    I am waiting for our FIOS connectivity and am presently using EMBARK DSL in its place. As an interim measure I want to add a second DSL to get more throughput. 1. Can this be done 2. Should both DSL modems ahve the same static ip from the provider Any help would be greatly appreciated Thx - Joe

    Surfsupjoe5 pointsBadges:
  • Commands for binding or mapping Layer 2 data to Layer 3 ports

    I have a question concerning Layer 2 and Layer 3 data on the same device. We have a client that will be sending us Layer 2 data streams, but we have to send them to a device that will only take IP multicasts. We will be using a Cisco 7600 Router with a 6700 Switch Card installed. If this is...

    NetworkingATE1,545 pointsBadges:
  • Cable for DTE/DTE

    Hello, I need a cable for two DTE, one is RJ45 and other DB9. The cable should be RJ45M to DB9F and Nullmodem rule. How can I get this cable? Can I make it? Can I use CISCO 72-3383-01 CONSOLE CABLE RJ45 - DB9 for this matter? Regards, Hamid,

    Aryanhr5 pointsBadges:
  • How to network VLANs together

    What can be done for different VLANs to communicate including a router in a network, i.e., the commands when configuring on a router?

    NetworkingATE1,545 pointsBadges:
  • Layer 2 vs. Layer 3 generic routing encapsulation (GRE)

    What is the difference between Layer 2 GRE and Layer 3 GRE?

    NetworkingATE1,545 pointsBadges:
  • Can you be annonymous on a guest VLAN?

    We have a network with multiple Vlans seperating departments etc. We have a guest Vlan for people to use that need access to the internet. We need to find a way of stopping the guest users from being able to 'see' each other within the guest Vlan. I can only think of seperating each user into their...

    Lukesacramento30 pointsBadges:
  • If my network’s configured incorrectly, how are my computers communicating?

    I have a question regarding communication within a local network. Please correct me If I am wrong: If there are two computers in a local network, Computer (A) and Computer(B), and if (A) wants to communicate with (B) or vice versa, then the request first strikes the router's LAN interface, right?...

    NetworkingATE1,545 pointsBadges:
  • Bladecenter T + JS20+ cisco 25R5391 SOL

    I have a bladecenter T and a js20 powerpc blade, as well as a cisco 25R5391 Layer 2 switch. I am trying to establish a serial over lan session to the js20 blade, but the sol status shows 'not ready' even after i add all the switch ports to the same vlan. on another note the 4 external ports on the...

    Baseline0x035 pointsBadges:
  • multiple lans, subnets, dsl connections on the same cables

    well this is my first post and its a doosie. At lewast for me. Looking for an all wise network guru!! =] we had an existing network consisting of 10pc's, a win2k server and a dsl connection. all was fine... dsl router:192.168.0.1 server: 192.168.0.10, 192.168.0.50 easy as pie... now we are partners...

    Jabooma15 pointsBadges:
  • Routing VLANs to public IPs from Intranet through Fortigate firewall

    We have three virtual local area networks (VLANs) as follows: 1 data, 2 voice and 3 wireless. We have 6506e at the core, and interVLAN routing is working fine. The problem is implementing FortiGate firewall in transparent mode and terminating the ISP on the router with Ethernet output. I am not...

    NetworkingATE1,545 pointsBadges:
  • Router configured one hop from PC with default gateway as IP address

    What would happen and what would be the flow if I configured a PC with the default gateway as an IP address of the router that is one hop away -- that means, I have one more router in between?

    NetworkingATE1,545 pointsBadges:
  • Connecting 2, 3 or 4 sites over MPLS

    Hi. I have some routing experience but I don't have much experience routing over a service providers MPLS network and had some questions.. Say I had 3 sites in different cities. I want to be able to route my data traffice to each site. I would like to use a MPLS provider. Does the provider hand-off...

    ChicagoTechie5 pointsBadges:
  • How many switches can you have in a network?

    What happens if I add more switches in the network? Is there any limitation or any calculation for that?

    NetworkingATE1,545 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following