• configure-cisco-2811-for-ethernet-p2p

    Hello, I have to configure a Cisco 2811 router that have 2 Fast Ethernet interface, in order to have a p2p connection with my ISP. The FastEthernt /0 will be used for the p2p connection with the ISP, the FastEthernet /1 will be used to route my pubblic IP. In order to make the connection the ISP...

    Rocconeri5 pointsBadges:
  • Components and cables to design/build a network

    Hello there, I would like to design-build a network for a small company (about 80 employees). The company is divided in 3 sections which are: designers (30 employees), sales (30 employees) and administrator/marketing (15 employees). Also there are 3 managers and a CEO. What components do I need to...

    AppliedInformatics35 pointsBadges:
  • Cisco 1841,SDM will not connect nor install

    I am trying to install a VPN Server on my Cisco 1841 router. When I try to connect SDM it will not connect. I tried reinstalling the SDM on the router, but it comes to a stage & says "copy operation failed". I tried to install VPN through CLI, but the CLI doesn't recognize the CRYPTO command. Need...

    Aslamalikhan25 pointsBadges:
  • How to check the loop in Cisco router?

    i want to know to how to check whether is a loop occurred in the network? because load in tx and rx in increasing...

    Hack0505 pointsBadges:
  • problem with sharing internet in wireless network using dsl-2640u

    Hi I have D-Link dsl-2640u modem.i've connected it to my pc with cable and i can access internet but i can't access internet in wireless network.i've tried to connet with a notebook wireless I don't know what to do! help me please.

    Rapfreak5 pointsBadges:
  • Help with site to site IPsec VPN between Cisco ASA 5505 and Allied Telesys AR450s

    Hello, I am trying to get an IPsec VPN built between a Ciso ASA 5505 and an Allied Telesys AR450s, but am encountering a strange issue. Layout

    Newtmonkey5 pointsBadges:
  • cisco 2950 configuration

    Hi, I have got a really stupid question to ask. I am running a small wireless internet service, about 20 customers so far. I'm using 4 access points to send out my signal. My input is from a t1 line into a cisco 1841 router. Here is where my problem starts: I've been using soho dsl router/switch ...

    Edcockrell35 pointsBadges:
  • Accessing a Server on a different subnet

    I have a t1 line that goes into a switch, off the switch there are two routers one operating on the subnet 192.168.1.1 and the other on 192.168.0.1. Both routers have individual static ip addresses. I have a ReadyNAS storage device on 192.168.1.100. I want to be able to access the server from both...

    Admccurdy5 pointsBadges:
  • Private IPv6

    Does IPv6 have private address such as IPv4's 10.0.0.0 or 192.168.0.0? Or is there a way to get an IPv6 address and roll back to a private IPv4 address on a Router?

    Grimm085 pointsBadges:
  • Can I use Windows server 2008 as a router?

    Can I use a Windows server 2008 as a router and a DHCP relay server? If so how?

    Troubleshooter24755 pointsBadges:
  • how to get into router, previous tech did not leave password.

    hi all, I just took place of last I.T. tech on new job, the previous tech did not leave the correct u/n and p/w how do I go about getting into switch and routers (cant do hard reset these machines are live) another issue they built exchange server on a partition, what will I have to do to get more...

    Arcolino20 pointsBadges:
  • Loop is seen on router but line protocol is down

    Loop is seen on router but line protocol is down, where could be the issue?

    Rohanpatil8885 pointsBadges:
  • Routers for cable connection with print sharing.

    We want to connect 2 computers thru one cable connection. My concern is that 1) it will slow the connection down so much as to make on line gamming difficult, 2) our cable modem is very very very old but reliable and 3) security. Routers have come a long way in security features but will adding...

    JAMNTHIS10 pointsBadges:
  • configuring L3 switch to router

    I have router having public address in F0/1 and S0/0 I have no firewall, Hence i am connecting Cisco 3560 Switch directly to the router. but i am anable to ping from my local vlans to the S0/0 I tried Nat and all the thing by switch port and no switch port commands. Every thing i tried. I i come...

    Ekansh400 pointsBadges:
  • Switches, Router for Call center?

    Helping a friend with a call center for an NGO in spare time. There would be 100 workstations & 100 VOIP phones. What switches and routers do I need to put this call centre together and run the phones with power over Ethernet? Any information about CRM/ACD etc would be appreciated. Thank you in...

    TrickedAce5 pointsBadges:
  • Layer 3 switch or router ?

    I am looking at having multiple networks created at the same premise. Each one will run a zone with work stations and servers. I am a bit confused between multiple routers and a layer 3 switch ? What do you guys suggest ?

    Aromalrajagopal55 pointsBadges:
  • What causes a router to hang?

    What causes a router to hang or hangup?

    NetworkingATE1,545 pointsBadges:
  • Configuration of Cisco router 871.

    am new to this filed. am now working in one isp. here some customer request public ip ( for example subnet 255.255.255.252) . for internet connection .in wimax connection. its possible to configure both public and private ip both on lan interface . or i should create  nat pool, which will be best...

    Asstnetworkengg25 pointsBadges:
  • DAP-1160 wireless G Access Point problem

    I Have DAP-1160 wireless G access point. Why the STATUS led is not blinking? My pc won't rekognize it. it worked befor reseting, after that the STATUS led does not blink.Not even when it;s connected to the pc. What is the problem? Can this problem be solved? Please help

    DeNashH5 pointsBadges:
  • Configuring managed switch and router in order to have Internet…

    Dear Sir, Could you please help me concerning the following matter: I have Cisco Catalyst 2950 managed switch connected to Linksys WRT54G - Wireless-G Broadband Router, which is then connected to ADSL modem. I need the following scenario: -two VLANs configured on the managed switch, so there will...

    Ivoivo0 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following