• Setting up a large home network

    I have a large home and the setup looks like this.  Cable Modem | Dynex Router - 192.168.1.1 - 255.255.255.0 | Belkin Wireless Router 192.168.2.1 - 255.255.255.0 My problem is that the Belkin works very well in all rooms except the far end of the house.  So I purchased a second Belkin Router...

    Ltannenbaum5 pointsBadges:
  • What brand of routers/switches do you trust the most?

    We're wondering what everyone is using for a brand of wireless routers and switches? What do you prefer to use in the enterprise versus at home or in personal networks? What are your suggestions for SMBs to large corporations? We've got 150 knowledge points for our favorite answer!

    MelanieYarbrough6,345 pointsBadges:
  • Limit Port 80 Time_Wait from my computer to router

    How can I limit the number of requests my computer makes to my router to port 80. At idle, when looking at the connection page of my router I see a hundred or so port 80 Time_Wait from my computer address (say 192.168.1.145) to my routers address (say 192.168.1.1).This has just started probably...

    Caji5 pointsBadges:
  • How to open NAT on Netgear WNDR3400 router?

    how to make nat open for netgear wndr3400?

    Saltwaterfishing5 pointsBadges:
  • LAN Connection between PC and Laptop

    I have a Netgear router installed on my home desktop PC.  It has been connected to my laptop and working just fine for at least a year.   After problems with my laptop, I re-installed XP and  I can't get the router to reconnect.  It keeps telling me the LAN has been unplugged.  When...

    CindyLThompson5 pointsBadges:
  • VPN Tunnel Configuration in Router uses BGP Routing Protocol

    How to create VPN Tunnel in Router which uses BGP as Routing Protocol and the client side Router also using BGP as Routing Protocol. Please guide me in this.

    Ajsdaj5 pointsBadges:
  • How do you get the VLAN protocol to go ‘up’?

    I've forgotten some information on VLAN protocols. I am butting my head against the wall right now trying to get the VLANs on my Cisco 2811 router to change to up/up from up/down. Does anyone know how to get the protocol of a VLAN to go “up”?  I’m just plain forgetting it all right...

    NetworkingATE1,545 pointsBadges:
  • ACLs for Lab 6 Packet Tracer

    Im trying to create an acl to permit and deny certain hosts to access certain services. below is the criteria, but for some reason my ACL doesnt accomplish the requirement.  Would you help please?? allow tw-dsl host web access to the Intranet server  allow tw-cable host access to the Intranet...

    Mellie5 pointsBadges:
  • How do you get the VLAN protocol to go up?

    I've forgotten some information on VLAN protocols. I am butting my head against the wall right now trying to get the VLANs on my Cisco 2811 router to change to up/up from up/down. Does anyone know how to get the protocol of a VLAN to go "up"? I'm just plain forgetting it all right now.

    ITKE344,850 pointsBadges:
  • What is the multicast IP address reserved for RIP2?

    What is the multicast IP address reserved for RIP2?

    Yasir Irfan5,535 pointsBadges:
  • Added computers not recognizing Linksys router, network down

    i need to reset my network but none of my added computers are recognizing the router wrt54g do i need to change the name of my network. the network went down while i was awy for a couple of days and never has come back up.

    061015 pointsBadges:
  • cisco router 2811 vpn

    Hi, is it possible to have both site-to-site and client-to-site vpv on the same interface dialer???

    PerseasFather5 pointsBadges:
  • How to make this DMZ routing work?

    Currently we have the DMZ ACL in the ASA firewall. One interface that was assigned as DMZ was connected to the core switch and within a VLAN. The server that was untagged to this DMZ VLAN will have the DMZ ACL applied to the inbound/outbound traffic.  This was quite simple setup.  This issue now...

    springman95 pointsBadges:
  • How to define local bandwidth and international bandwidth on Cisco 3845 with 2960 switch

    I have a 1gb local bandwidth with 10mb international bandwidth in my data center. and my problem is i don't know how to share the international bandwidth equally to my clients. I don't know if there are device i need to use or is there are anyways i could just control the international bandwidth....

    Bosslui5 pointsBadges:
  • Getting Ping Timeouts from Cisco 2948G-L3.

    Hello, I have Cisco 2948G-L3, the problem i am facing is that i am not getting ping response from the router. The senerio is that i have configured 192.168.1.1/24 in fa 1 and 192.168.1.5/24 in directly connected PC. Router is also sensing the port status, when i plug the cable in it, it shows port...

    Hab345 pointsBadges:
  • Blocking internet access except Outlook

    I WORKED WITH ONE MENUFACTERING COMPANY ,IN MY COMPANY WE R USING INTERNET WIA LEN , NOW I HAVE TO BLOCK THE USER TO USE INTERNET EXCEPT THE OUTLOOK, ONLY FEW MACHINE I WANT FULL ACCESS OF INTERNET SUGGEST ME FOR BLOCKING INTERNET,ISP COMES TO ROUTER & FROM ROUTER IT GOES TO SWITCH, FROM SWITCH...

    Rajdip10 pointsBadges:
  • TCP/IP limits on routers/switches

    Does anyone know if there are limits using a router/switch or separate routers and switches for the number of users online (not twinax local terminals but remote terminals) concurrently? I know multiplexers on mainframes would allow modems to allow many terminals at one time...and the terminalID...

    Gmil494365 pointsBadges:
  • layer 2/3 switches

    When I am trying to put the default gateway in layer 2 switches with ip default-gateway xxxxx commnd it ok. But If I'm trying to put the default-gateway in 3560(layer 3) switches with ip default-gateway xxxxxxx command its giving me error that invalid command

    Jadu50 pointsBadges:
  • Measuring a wireless router’s signal strength

    How can you measure your wireless router’s signal strength? Can it be boosted? And what router has the best signal strength right out of the box?

    TeachMeIT975 pointsBadges:
  • Wireless Router

    I have a Linksys wireless G router connected to a cable modem. In my home I have a desktop computer with a USB Linksys wireless external card connected to it. I also have a Toshiba laptop with an internal wireless card. These both talk to my router and can get to the internet but it is an unsecured...

    JimR JDEWorldA9115 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following