• Trouble configuring two Cisco 1310 for building-to-building Wi-Fi

    I tried to connect 2 Cisco 1310 for a building to building connection via Wi-Fi. I used the following sample configs found in this tip, called Configure Cisco wireless bridges for point-to-point networking. One the Cisco 1310 Access Points/Bridges starts up and the connection stays up for a few...

    NetworkingATE1,545 pointsBadges:
  • Configuring two WAN links between two locatons

    My central location is connected with remote location through 64kb/s VSAT link for accessing web applications of central location from remote location. remote location is having cisco 1600 sereis router and remote location 2800 sereis router. Now we have hired another 512 kb/s vsat link between...

    Dobhalg10 pointsBadges:
  • router

    I was thinking about buying a laptop and a linksys router but i wanted to know if the PC and my laptop could both be on the computer at the same time. My PC is a dell, ISP is DSL and its current 'router' is a westell model 2200. I also had another question. If i brought my laptop over to someone...

    Jmonkey10 pointsBadges:
  • Cisco 2811 router and need to create a VPN

    I have a Cisco 2811 router and need to create a VPN to another site but not sure what their endpoint device is. What I am looking for is a white paper on how to configure the Cisco router for a VPN. Can anyone help me?

    Cyberref5 pointsBadges:
  • We have an internet connection from 2 different ISP, I want to use the same PIX 525 firewall 7.0(6)

    We have an internet connection from 2 different ISP, I want to use the same PIX 525 firewall 7.0(6) . My firewall has 2 Ethernet interface & 2 Giga Ethernet interfaces. I am using ethernet 0 for outside connection with ISP A ethernet 1 for outside2 connection with ISP B Giga Ethernet 0 for DMZ zone...

    Yasir Irfan5,545 pointsBadges:
  • Linksys systems error message-help

    When I open my service I get the following message: access violation @address 004074CDin moduleWMP54GSv1_100000368 -Linksys Wireless Network Monitor. Any suggestions for a fix?

    Cronewoman20 pointsBadges:
  • What hardware is needed for VPN

    Hi Guys, I'm hoping you can help me. I need to find out what extra hardware I will need to get to provide VPN access into my workplace. We currently have a DSL connection into a Westell 2200 Modem into a Linksys BEFW11S4 router into a Windows 2003 server with one nic. My questions are: 1) Do I need...

    Fullonjohn5 pointsBadges:
  • Routing Virtual IP Address.

    We have 2 Windows 2003 Terminal Servers and both are part of load balance with a Single Virtual IP Address. For Eg 192.170.2.34 is virtual ip, and any User tries to connect to this ip address will be diverted to any one Server IP eg 192.179.2.33 or 192.170.2.32. accoring to load. But when users...

    Mysore0 pointsBadges:
  • Layer 3 switch

    Can we use layer 3 switch as a router on a dissimilar network ? define dissimilar network with example?

    Fahimalavi10 pointsBadges:
  • upgrade cisco aironet access point 1130 from autonomous to lightweight

    please how to upgrade cisco aironet access point 1130 from autonomous to lightweight , how can i do this step by step

    Cisco solutions5 pointsBadges:
  • CISCO 2811 ETHERNET CONFIGURATION

    I am using CISCO 2811 router. This CISCO router has a LAN connected via a switch on one side and the ISP via a fibre on the other end. The router looses internet connection periodically, up to seven (7) times every day and this interrupts office work. when I shut down ethernet zero (0) and bring it...

    Gentle5 pointsBadges:
  • CISCO 2811 Scalability

    I have a CISCO2811 Router with two Fast Eth ports. Whether I can add one more module. Whether I can have a bandwidth of 8Mbps WAN in one of my Fast Eth ports. Whether I can balnce two ISPs in this CISCO 2811

    Mss5 pointsBadges:
  • router attached to cable modem

    I just got com-cast digital cable for the internet. They said in order to run two computers at the same time (each person surfing different locations) I will need a network "HUB". I was told by them that a switch would work just fine and would plug into the modem as the modem only allows for one...

    Dummy5 pointsBadges:
  • having a drop in wireless connection

    I have a wireless network setup with a Linksys 160 now, it was on a netgear. i change wireless routers because i thought that it was the router that was the problem, but it isnt. My computer and a PS3 are both hardwired to the router, my parents computer and laptop and my PSP are wireless....

    Shady9015 pointsBadges:
  • Inter VLAN Routing

    I amm using two cisco 3750 and I want Interdomin routing. I connect two host to one 3750 and make a trunk to communicate with other 3750. Ping from host to switch(Directly connected to host) is ok. ping from switch to switch is ok(Through trunk) But when i ping a host to swich that is via trunk,...

    Hmittle5 pointsBadges:
  • Router for Hughes Satelite System

    I have 5 Computers, all Hp Media centers 1 Windows XP Pro my main computer 2 hp Windows Vista Home Premion media computers and 1 laptop Vista Home Premion all desktops 2.66ghz dual 64 Amd processors; the laptop is an Intel 3 ghz dual 64 processor; I need to purchase a Router to connect them into a...

    Octal45 pointsBadges:
  • Two Internet Connections, One server

    OK, I'm very, very new to networking. Please be kind. I work for a small company. We have a server running Lotus Notes that is accessed both by people inside our LAN and about 50 employees that connect over the internet. Our internet connection is a simple DSL. We recently installed a hi-tech phone...

    JMackey20 pointsBadges:
  • Cisco Pix inside no nat to router that nat’s

    Hi, I have a Cisco Pix which currently has an internal, dmz and outside interface. My outside is my default route, however I have now new separate connection (interface 4) that connects to the internet also that I would like to route some outside bound traffic through. As i understand it you can...

    Mawk100015 pointsBadges:
  • Deny DHCP and Network access to rogue wireless routers

    We are running a MS DHCP network and home wireless routers are finding their way in. I scan the DHCP scopes daily and thought I was denying their ability to connect by creating a reservation for the MAC address and modifying the configuration options for the device. I set the following options to...

    Twhite0 pointsBadges:
  • I’m using wireless netgear router and i can’t share printer.

    I'm using wireless netgear router and i can't share printer....please help how do i do that.thx

    Xxx385 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following