• Dell laptop NIC problems

    Hi, One of my colleagues has a Dell Latitude D510 running Windows XP. When connected to our LAN, the laptop is unable to obtain an IP address. When I view the network card in Device Manager, it appears to be installed and working correctly. The NIC is a Broadcom 440x 10/100 Integrated Controller. I...

    Nickc197665 pointsBadges:
  • Laptop cannot detect home WLAN server

    I have two T42 laptops which connect to a Siemens Gigaset Wlan server. One has been used by my son at boarding school and the settings have probably been changed. It now does not see the home Wlan server any more, even so it still sees weaker servers in surrounding houses. The second T42 sees and...

    Wlannovice15 pointsBadges:
  • SCSI Boot with IDE, old CMOS

    Compaq Deskpro EN 733/512 with Windows 2000 Server booting on 9GB SCSI drive, Adaptec controller. Active Directory, Domain Controller, WINS, file/database server. Drive getting full, Non-Profit on the Cheap, picked up a large IDE drive hoping to simply add it. Life is for learning, now I understand...

    VietBob0 pointsBadges:
  • Is it possible to lift router-based bandwidth caps (if they exist)?

    like the title says, is it possible to lift a router based bandwidth cap (if one exists) on my router. im only pulling about 100kb/s on a DSL line. i dont have a wireless setup running, jus straight cat-5 from the router to my cpu. i would assume capping would be done server side, but someone said...

    Stress5 pointsBadges:
  • Problem in Linksys Wireless G ADSL Home Gateway

    Hi, I am using Linkys modem (model : annex -A) i am configure the modem using rechargable card,encapsulation is RFC 2516 pppoE,multiplexing is LLC,qos type is UBR,autodetect is Enabled,Dsl modulation is ADSL2+, vpi/vci is 0.35, after save changes i see the stsatus interface is up, but i try to...

    Elite20 pointsBadges:
  • Central Router to assign the same IP address to the VPN Clients

    i have several PCs connecting to a central site router using the VPN Client and different media (DSL, ISDN, UMTS). I would like the central router to assign the same IP address to the VPN clients each time they connect again to the central site. So far I have an IP pool configured on the central...

    ITKE351,965 pointsBadges:
  • Can I use a Linksys BEFSR41 as a hub connected to a Linksys WRT150N?

    I have replaced my BEFSR41 VER 3 with a WRT150N. Can I use the BEFSR41 as a hub connected to the 150N?

    Grntech5 pointsBadges:
  • Need help with small wireless network

    if i have a wireless N router and i want to hook up a desktop at the other end of the house up with a network adapter do i need an N adapter or can i use a G?

    Raremold201010 pointsBadges:
  • How to connect a server using DSL routers

    My company is having 30 users at different different location all of them is having separete DSL routers with a VPN tunnel ... And i wanted to connect them to the main server and create a active directory to deny using the cdrom,startmenu, flash drive, games and etc they should only use the company...

    Sufisnetwork5 pointsBadges:
  • Need help with VLAN configuration

    I have a router connected with Fast Ethernet to switch in VTP Server Mode (containing 2 VLANs) and then connected to a switch in transparent mode with three VLANs and after it a single switch in client mode. All these switches belong to the same domain and I have done interVLAN routing in it and...

    NetworkingATE1,545 pointsBadges:
  • Switching ISPs and need help reconfiguring VPN and Firewall settings

    When switching from DSL to Cable Internet... when you have a router w/VPN & Firewall and a static IP - how do you switch the service? Obviously just plugging the new service provider in won't work. I know you need the log in and password to the router but after that?

    NetworkingATE1,545 pointsBadges:
  • 4 VLANS, 3 locations, 3 Routers, No communication between Lans or VLANs

    OK, here is my problem, I'm working on a project in the Test phase right now. I have 3 routers (Cisco 2811s), all running EIGRP, these are seperating 3 goegraphical regions. Each of these Routers is linked via Trunking line to a Switch which has 4 VLANs enable. According to everything I have found...

    CRagsdale32755 pointsBadges:
  • Configuring Cisco 1700 with Cyberoam box

    This is regarding the Cisco 1700 series router, which has been configured by some other experts. We are now having a lease line and the Cisco router connected with Cyberoam box. Earlier we had an ADSL connection, so I had direct IP where there was no need to logging into Cyberoam everytime. But...

    NetworkingATE1,545 pointsBadges:
  • How does one setup a Windows 2003 Enterprise Server on one machine with 2 nics?

    I have read a book (O'Reily) on setting up windows server 2003 and at my current job I am fortunate enough to be able to work/play with their servers which are also windows 2003. In this, I have a bit of experience, however I ran into a few problems when trying to setup my own personal network at...

    Pr0970 pointsBadges:
  • Does RIP support discontinuous networks?

    Does RIP support discontinuous networks? I configured a discontinuous network in a simulator and it works there, but I want to know if it works in the real world.

    NetworkingATE1,545 pointsBadges:
  • How to add a subinterface in Cisco 2811 router

    how to add a subinterface in router 2811

    Fsheb5 pointsBadges:
  • Is AES the best encryption for enterprise routers

    Is AES the best encryption for enterprise routers? How many letters& alpha numberic keys need for AES password?

    Spock12035 pointsBadges:
  • Linksys router issue

    We are a small organization using Linksys WRT54G wireless routers in a section of our offices. One router will not accept a change from WEP to WPA2. Attempts to update the firmware (in the hopes that this would resolve the issue) fail both from the external updater and from within the router...

    Pressler29042,190 pointsBadges:
  • Using switch or router ACL to block streaming traffic

    I would like to block streaming media requests using either the LAN switch or the site edge router. The site is on a private network and does not have a local firewall at the edge. Has anyone used Cisco ACL's for this purpose and if so, how did you do it? Or, would I be better implementing a...

    Labnuke9932,960 pointsBadges:
  • Cisco 2811 router with Ethernet access to MPLS

    Can a Cisco 2811 router support a 40Mbps MPLS connection using Fast Ethernet access?

    Webonauta15 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following