• how to switch the traffic inside the router?

    I have one router wich connect to two lines one is ADSL line and one is leased line and i want sone trafic to go throue the ADSL line and some of the throue the leased line but i dont know how to do this switching between the two lines.

    Mohadbazzi47170 pointsBadges:
  • how can we configure a 36 port router?

    how to install, configure and use a cisco 36 port router?

    Arun2gautam5 pointsBadges:
  • is it possible that two different technologies (adhoc and ethernet ) work at same time on Data Link Layer

    supose we hv 3 systems. centerlised system hv 2 lancards. one PCI card of realtek and second wireless of linksys. PCI card ip address is 192.168.1.1 and its connected system ip address is 192.168.1.2. wireless lancard address is 172.168.15.1 and it connected wd other wireless system address...

    JustCCNACWNA5 pointsBadges:
  • configuration of a new router

    I WAS CONFIGURING A FRESH/NEW RUTER OF CISCO SERIES 1841 FROM A CONSOLE ON A HYPER TERMINAL.THE ROUTER WAS BROUGHT IN ROMMON MODE AND WRONGLY TYPED CNFREG-REGISTRY 1024 AND GIVEN THE COMMAND.AFTER THIS COMMAND ROUTER STOPS ACCEPTING KEY COMMAND AND HYPER TERMINAL BECAME BLANK .I SWITCH OFF THE...

    VADERA10 pointsBadges:
  • commands for nortel ARN router against cisco 1700 series router

    as i was using cisco router and now i want to installed nortel ARN router in place of that. I have configuration backup of cisco router,so i only want Nortel ARN router commands to configure against cisco commands

    Networkfresher5 pointsBadges:
  • Configure wireless networks to dynamically switch between leased lines

    Can you send me instructions on how to configure two seperate network setups; a leased line and a wireless network setup to work together? Both are connected to a central network where there is a layer switch. Is there a way to setup the leased line to auto-connect upon wireless failure and...

    NetworkingATE1,545 pointsBadges:
  • Differences between integrated service router and modular access router?

    What is the difference between an integrated service router and a modular access router?

    NetworkingATE1,545 pointsBadges:
  • WAN configuration

    how configure the central router in central office? how configure the router in remote branch office ? please,give me a sample configuration of central router configuration in central office. LINE :E1 FOR CENTRAL OFFICE BANDWIDTH OF BRANCH OFFICES:256 KBPS ROUTER IN CENTRAL OFFICE : CISCO 3800...

    Alioroumi5 pointsBadges:
  • Cisco 2811 Fast Ethernet and LAN configuration

    i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

    JACK15705 pointsBadges:
  • best routing protocol for frame relay network

    what is the best routing protocol to use when seting up a frame relay network

    ITKE828,295 pointsBadges:
  • Cisco 3700 router with 2 seperate networks

    i have 2 different networks (181 and 180) running to the same router. i would like for them to "talk" to each other. how would i do this?

    ITKE828,295 pointsBadges:
  • ROUTER INTERFACE

    IN ROUTER , ON SERIAL INTERFACE I AM GETTING POO RELY 201/255       WHAT CAN BE PROBLEM

    VADERA10 pointsBadges:
  • SNMPv3 Configuration with HP OV

    I am trying to configure snmpv3 using HP OV on a cisco router. The router has been configured properly to run snmpv3 already. I then edited the mgr.cnf file on the server located at /etc/srconf/mgr to add the following entry: usmUserEntry "agentEngineID" snmpv3user usmHMACMD5AuthProtocol...

    Phrathepmali30 pointsBadges:
  • configuring static route

    there is to style to configure the static route one with the source and destination ip address and one with 8 zeros and the destination ip address,so when we use each one of this two style?

    Mohadbazzi47170 pointsBadges:
  • HTU-E1 Leased Line Modem

    hi,can anyone tell me how to take loop test on HTU E1 Leased line modem to test physical connectivity

    Xevier0 pointsBadges:
  • Software based WIN Simulation

    Hi, I need to test out an application over WAN. The testing includes the response time with different delays and bandwidth requirements. Is there any piece of software (preferably opensource/freeware)which can simulate the WAN for me? The idea is to install two NICs in the Windows/Linux machine,...

    SADnBLUE0 pointsBadges:
  • isp connection

    i have an isp line. i want to increase the speed of downloading and browsing.i want to know what router or manual switches will cater my need.

    THE NET GURU5 pointsBadges:
  • how to configure PA-MC-STM1 card in cisco 7206 router

    I want to know how to configure PA-MC-STM1  card in cisco 7206 router

    ITKE828,295 pointsBadges:
  • Cisco 2801 router noise

    I am having Cisco 2801 router & from last one day too much sound / noise is coming from this router.I have checked & in router showing fan 2is faluty but fan 1 is working..pls suggest solution ..

    ITKE828,295 pointsBadges:
  • I want use a D-link Dir-600 router that will sit behind a Cisco router with 2 vlans

    I have an application where I have setup a Cisco 1841 router with 2 vlan connection's, I want to setup a wireless D-link DIR-600 wireless router on one of vlans so visiting venders can get to the internet without being on my network. Do I need to setup the D-Link router with any VLan...

    Shedman35 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following