• hub and spoke using EIGRP

    I cant ping from one spoke to another, split-horizon has been disabled, any suggestions???

    Rayb5315 pointsBadges:
  • Connecting Home Router to Switch

    Yhpctdon20 pointsBadges:
  • Resetting Wireless Routers

    How do I get around the username and password on a Negear WGR614v7 wireless router?  Someone else set this up and I do not have the username and password, but need to reset the security on it. Thanks, Dan Maguire dan.maguire@hotmail.com

    FireSide315 pointsBadges:
  • Router Re-Configuration

    When I type the IP address of my router in the Explorer address bar. It replies this web page cannot be opened. IP address 198.162.1.2

    Samdog5 pointsBadges:
  • SETTING UP LEGACY ONE CHANNEL CAMERA SERVER

    WORKING ON THE BASICS.     1 My web server is a GV-ITIC01, a single camera web server.    2 My Router is a Westel327 wireless. In setting up the configuration of the routers ports... I am trying a variety of configurations in order to get a connection outside my router on a laptop.  Westel...

    Lancersdad5 pointsBadges:
  • vsat connections using router

    How do i connect my two office via vsat using routers?

    Patilnet65 pointsBadges:
  • hi all

    last day i installed one new xp theam on my xp system. recently i noticed that "RUN" option deleted from my start menu. can anybody help me in this problem ? thanks in advance

    Squibc40 pointsBadges:
  • Router Troubleshooting Cisco 7500 series

    can any one tell me how to check which interface is utilizing more bandwidth in high end routers(7500 ,10000 series) if so many interface are configured? since we cant check each and every interface at the time of slowness.

    Planetxmi15 pointsBadges:
  • dial up and router

    Is it possible to use a router with a dial up connection?

    Sqeeter915 pointsBadges:
  • Cisco Router 857 Faulty?

    Hi, I have a csico router 857 that appears to be faulty. When i connect to it using hypert. or 'putty' there appears to be no config. on it. All of the info. is scrambled - making no sense. Is there anything i can do about this..or is it RTB? regards and thanks in advance PT

    Pelvicthrust170 pointsBadges:
  • Need help on ppp config on Cisco 2600 router

    We are upgrading our point-to-point private line from single T1 to two T1 lines. I have installed the DSU/CSU module to the router. Working on the new configuration but found the ppp code I put in doesn't work. I can't figure out what was wrong. If you could give me a hand, that would be very very...

    springman95 pointsBadges:
  • Router Related Questions

    IT professional, Who are going for the written test on different networking administration, need some sample questions and solution related with Router.   Please help me. Thank you. 

    BIFT55 pointsBadges:
  • network problem

    Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router

    Krishnabthapa5 pointsBadges:
  • router to tftp server software copy

    I want to copy new software from tftp server to my router and i tried many times but its failed so any one know the way to do that

    Mohadbazzi47170 pointsBadges:
  • Ping Issue across three routers

    I have a network of three routers.Router A is pinging Router B & Router B is pinging Router C but Router A is not pinging router C.What can be the problem???

    Sayub40 pointsBadges:
  • Two Subnets – Three Routers + DSL Modem

    Is the following setup valid for creating two subnets (192.168.2.xxx and 192.168.3.xxx) that both access a single internet connection but are isolated? ROUTER A WAN --> DSL Modem ROUTER B WAN --> ROUTER A LAN  ROUTER C WAN --> ROUTER A LAN  Settings: Router A  WAN - PPoE, etc. etc. LAN...

    Hashlock5 pointsBadges:
  • 20% packet loss affects performance?

    Hi. I've been noticed that I have some packet loss when I do ping from our 3Com router 5642 to the default gateway of our provider. <codinet03>ping 10.162.66.185 PING 10.162.66.185: 56 data bytes, press CTRL_C to break Reply from 10.162.66.185: bytes=56 Sequence=1 ttl=255 time=3 ms Reply from...

    Cabo8135 pointsBadges:
  • wireless router, desktop, and laptop

    I have high speed internet service. I have a telephone line that plugs into a modem from verizen (model 6100) The phone line goes directly into the dsl plug. The desk top is conected by ethernet cable and the only thing left is a usb spot. How am I going to hook up my new wireless belkin G router...

    Smiller795 pointsBadges:
  • Dell Optiplex GX520 hibernation/sleep mode issues

    Hello, We have several Dell Optiplex GX520's on the network running Windows XP pro. They randomly fall into sleep mode. Moving the mouse will not wake them - you have to push the power button to get them out of sleep mode. Also we are not able to remotely wake them to do patch updates or remotely...

    Jmello0 pointsBadges:
  • how to switch the traffic inside the router?

    I have one router wich connect to two lines one is ADSL line and one is leased line and i want sone trafic to go throue the ADSL line and some of the throue the leased line but i dont know how to do this switching between the two lines.

    Mohadbazzi47170 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following