• network problem

    Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router

    Krishnabthapa5 pointsBadges:
  • router to tftp server software copy

    I want to copy new software from tftp server to my router and i tried many times but its failed so any one know the way to do that

    Mohadbazzi47170 pointsBadges:
  • Ping Issue across three routers

    I have a network of three routers.Router A is pinging Router B & Router B is pinging Router C but Router A is not pinging router C.What can be the problem???

    Sayub40 pointsBadges:
  • Two Subnets – Three Routers + DSL Modem

    Is the following setup valid for creating two subnets (192.168.2.xxx and 192.168.3.xxx) that both access a single internet connection but are isolated? ROUTER A WAN --> DSL Modem ROUTER B WAN --> ROUTER A LAN  ROUTER C WAN --> ROUTER A LAN  Settings: Router A  WAN - PPoE, etc. etc. LAN...

    Hashlock5 pointsBadges:
  • 20% packet loss affects performance?

    Hi. I've been noticed that I have some packet loss when I do ping from our 3Com router 5642 to the default gateway of our provider. <codinet03>ping 10.162.66.185 PING 10.162.66.185: 56 data bytes, press CTRL_C to break Reply from 10.162.66.185: bytes=56 Sequence=1 ttl=255 time=3 ms Reply from...

    Cabo8135 pointsBadges:
  • How do I preserve network communication among all schools on the network given the addition of three new routers on the network?

    Question: We currently have a flat network between seven schools in our school division using LANSPAN. Their is only one router in the network at our Central Office where all Internet traffic comes through. Now, fibre technology has been added to all schools with a router in place at each school....

    Skenny175 pointsBadges:
  • wireless router, desktop, and laptop

    I have high speed internet service. I have a telephone line that plugs into a modem from verizen (model 6100) The phone line goes directly into the dsl plug. The desk top is conected by ethernet cable and the only thing left is a usb spot. How am I going to hook up my new wireless belkin G router...

    Smiller795 pointsBadges:
  • Dell Optiplex GX520 hibernation/sleep mode issues

    Hello, We have several Dell Optiplex GX520's on the network running Windows XP pro. They randomly fall into sleep mode. Moving the mouse will not wake them - you have to push the power button to get them out of sleep mode. Also we are not able to remotely wake them to do patch updates or remotely...

    Jmello0 pointsBadges:
  • how to switch the traffic inside the router?

    I have one router wich connect to two lines one is ADSL line and one is leased line and i want sone trafic to go throue the ADSL line and some of the throue the leased line but i dont know how to do this switching between the two lines.

    Mohadbazzi47170 pointsBadges:
  • how can we configure a 36 port router?

    how to install, configure and use a cisco 36 port router?

    Arun2gautam5 pointsBadges:
  • is it possible that two different technologies (adhoc and ethernet ) work at same time on Data Link Layer

    supose we hv 3 systems. centerlised system hv 2 lancards. one PCI card of realtek and second wireless of linksys. PCI card ip address is 192.168.1.1 and its connected system ip address is 192.168.1.2. wireless lancard address is 172.168.15.1 and it connected wd other wireless system address...

    JustCCNACWNA5 pointsBadges:
  • configuration of a new router

    I WAS CONFIGURING A FRESH/NEW RUTER OF CISCO SERIES 1841 FROM A CONSOLE ON A HYPER TERMINAL.THE ROUTER WAS BROUGHT IN ROMMON MODE AND WRONGLY TYPED CNFREG-REGISTRY 1024 AND GIVEN THE COMMAND.AFTER THIS COMMAND ROUTER STOPS ACCEPTING KEY COMMAND AND HYPER TERMINAL BECAME BLANK .I SWITCH OFF THE...

    VADERA10 pointsBadges:
  • CLI config confirmation

    Hi, does anyone know if d-link is manufactured by cisco? There is this client that asked me on how to create multiple ip adresses on a single interface of cisco router, but the switch connected to it was a d-link switch. Of course, the solution was intervlan routing but I haven't seen a d-link CLI...

    Yeahboy900 pointsBadges:
  • commands for nortel ARN router against cisco 1700 series router

    as i was using cisco router and now i want to installed nortel ARN router in place of that. I have configuration backup of cisco router,so i only want Nortel ARN router commands to configure against cisco commands

    Networkfresher5 pointsBadges:
  • Configure wireless networks to dynamically switch between leased lines

    Can you send me instructions on how to configure two seperate network setups; a leased line and a wireless network setup to work together? Both are connected to a central network where there is a layer switch. Is there a way to setup the leased line to auto-connect upon wireless failure and...

    NetworkingATE1,545 pointsBadges:
  • Differences between integrated service router and modular access router?

    What is the difference between an integrated service router and a modular access router?

    NetworkingATE1,545 pointsBadges:
  • WAN configuration

    how configure the central router in central office? how configure the router in remote branch office ? please,give me a sample configuration of central router configuration in central office. LINE :E1 FOR CENTRAL OFFICE BANDWIDTH OF BRANCH OFFICES:256 KBPS ROUTER IN CENTRAL OFFICE : CISCO 3800...

    Alioroumi5 pointsBadges:
  • Network problems Cisco router config

    Hi experts, I want to connect with a web server in remote end using leased line connectivity through Cisco 2800 series router I have a flat network with 500 users in network. All PC’s default gateways are configured the IP of routers Ethernet. When I am ping the web server from LAN it is taking...

    Intrnetworking30 pointsBadges:
  • Cisco 2811 Fast Ethernet and LAN configuration

    i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

    JACK15705 pointsBadges:
  • best routing protocol for frame relay network

    what is the best routing protocol to use when seting up a frame relay network

    ITKE341,785 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following