• Configuring managed switch and router in order to have Internet…

    Dear Sir, Could you please help me concerning the following matter: I have Cisco Catalyst 2950 managed switch connected to Linksys WRT54G - Wireless-G Broadband Router, which is then connected to ADSL modem. I need the following scenario: -two VLANs configured on the managed switch, so there will...

    Ivoivo0 pointsBadges:
  • SUBNETTING

    Hi What is the broadcast address for the IP subnet 192.168.100.32 given a subnet mask of 255.255.255.224. I want to know step by step procedure on how to get the right ans. Brgds Mark

    Markmu5 pointsBadges:
  • Interview

    I have an interview on SCADA systems. Could anyone help with what kind of questions should i be expecting, they need someone with knowledge in everything right from communications,controls and database. (HArdware + Software).I dont have much experience on my resume but still they considered me for...

    Controls0 pointsBadges:
  • Is there any configuration on Cisco router to enable it to respond to ARP from IP source 0.0.0.0?

    When I configure my PC with a static IP the PC issues an ARP packet to the IP I configured with source IP 0.0.0.0 If any other PC (windows/Linux) have this IP I get a reply to my PC. If the Cisco router is configured with this IP my PC doesn’t get a respond to the ARP and this IP will be active...

    ITKE406,450 pointsBadges:
  • 2 VPN, 2 Network Cards – 1 Computer

    Is it possible to have 2 VPN with 2 Network Cards on 1 computer and have them both dial out at the same time? - I have a Cisco and a Sonic VPN that both need to connect to 2 different companies at the same time - can I configure them to point to different network cards/cables to a linksys box to 1...

    Lvg5 pointsBadges:
  • How could i telnet a router using router ID of that router ?

    Can i telnet a router using router ID of that router ??? Thanks in advance...

    Azharafridi5 pointsBadges:
  • Cisco configuration

    i have newly setup cisco 1841 router and i didn't create user and its password i just want to know that its default user or password will expired after 15 days or not. it is necessary to create user or password or not

    Kaleemu5 pointsBadges:
  • Wireless Routers with Static DHCP settings?

    We have an internal wired network that DOESN'T use DHCP. Client machines have their IPs set uniquely & their gateway & DNS settings pointing at a proxy server that gives internet access. I need to add wireless capability to this network. So the access point has to be able to have a hardwired IP,...

    ITKE406,450 pointsBadges:
  • Setting up a large home network

    I have a large home and the setup looks like this.  Cable Modem | Dynex Router - 192.168.1.1 - 255.255.255.0 | Belkin Wireless Router 192.168.2.1 - 255.255.255.0 My problem is that the Belkin works very well in all rooms except the far end of the house.  So I purchased a second Belkin Router...

    Ltannenbaum5 pointsBadges:
  • What brand of routers/switches do you trust the most?

    We're wondering what everyone is using for a brand of wireless routers and switches? What do you prefer to use in the enterprise versus at home or in personal networks? What are your suggestions for SMBs to large corporations? We've got 150 knowledge points for our favorite answer!

    MelanieYarbrough6,345 pointsBadges:
  • Limit Port 80 Time_Wait from my computer to router

    How can I limit the number of requests my computer makes to my router to port 80. At idle, when looking at the connection page of my router I see a hundred or so port 80 Time_Wait from my computer address (say 192.168.1.145) to my routers address (say 192.168.1.1).This has just started probably...

    Caji5 pointsBadges:
  • How to open NAT on Netgear WNDR3400 router?

    how to make nat open for netgear wndr3400?

    Saltwaterfishing5 pointsBadges:
  • LAN Connection between PC and Laptop

    I have a Netgear router installed on my home desktop PC.  It has been connected to my laptop and working just fine for at least a year.   After problems with my laptop, I re-installed XP and  I can't get the router to reconnect.  It keeps telling me the LAN has been unplugged.  When...

    CindyLThompson5 pointsBadges:
  • VPN Tunnel Configuration in Router uses BGP Routing Protocol

    How to create VPN Tunnel in Router which uses BGP as Routing Protocol and the client side Router also using BGP as Routing Protocol. Please guide me in this.

    Ajsdaj5 pointsBadges:
  • How do you get the VLAN protocol to go ‘up’?

    I've forgotten some information on VLAN protocols. I am butting my head against the wall right now trying to get the VLANs on my Cisco 2811 router to change to up/up from up/down. Does anyone know how to get the protocol of a VLAN to go “up”?  I’m just plain forgetting it all right...

    NetworkingATE1,545 pointsBadges:
  • ACLs for Lab 6 Packet Tracer

    Im trying to create an acl to permit and deny certain hosts to access certain services. below is the criteria, but for some reason my ACL doesnt accomplish the requirement.  Would you help please?? allow tw-dsl host web access to the Intranet server  allow tw-cable host access to the Intranet...

    Mellie5 pointsBadges:
  • How do you get the VLAN protocol to go up?

    I've forgotten some information on VLAN protocols. I am butting my head against the wall right now trying to get the VLANs on my Cisco 2811 router to change to up/up from up/down. Does anyone know how to get the protocol of a VLAN to go "up"? I'm just plain forgetting it all right now.

    ITKE406,450 pointsBadges:
  • What is the multicast IP address reserved for RIP2?

    What is the multicast IP address reserved for RIP2?

    Yasir Irfan6,790 pointsBadges:
  • Added computers not recognizing Linksys router, network down

    i need to reset my network but none of my added computers are recognizing the router wrt54g do i need to change the name of my network. the network went down while i was awy for a couple of days and never has come back up.

    061015 pointsBadges:
  • How to make this DMZ routing work?

    Currently we have the DMZ ACL in the ASA firewall. One interface that was assigned as DMZ was connected to the core switch and within a VLAN. The server that was untagged to this DMZ VLAN will have the DMZ ACL applied to the inbound/outbound traffic.  This was quite simple setup.  This issue now...

    springman95 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following