Router Configuration

ACLs for Lab 6 Packet Tracer

Im trying to create an acl to permit and deny certain hosts to access certain services. below is the criteria, but for some reason my ACL doesnt accomplish the requirement.  Would you help please?? allow tw-dsl host web access to the Intranet server  allow tw-cable host access to the Intranet...

configuration of a new router

I WAS CONFIGURING A FRESH/NEW RUTER OF CISCO SERIES 1841 FROM A CONSOLE ON A HYPER TERMINAL.THE ROUTER WAS BROUGHT IN ROMMON MODE AND WRONGLY TYPED CNFREG-REGISTRY 1024 AND GIVEN THE COMMAND.AFTER THIS COMMAND ROUTER STOPS ACCEPTING KEY COMMAND AND HYPER TERMINAL BECAME BLANK .I SWITCH OFF THE...

Bridge mode vs NAT or router mode

Could any one simply explain the differences between NAT mode Vs brdige mode? And can I configure the same IP range for WAN and LAN interface for a router whih con ein brdige mode? Is brdigne mode really requires IPs?   Thanks,   Software/Hardware used: router NAT brdige

configuration of auxilary port for cisco router

Hi, We need to configure a adapter for third party. vendor need to login via pstn thorugh this router. i can configure the cisco fax adopter but i dont know how vendor will login to this router please explain. can any body describe what is the scenario "login through aux port via pstn line" ...

Cisco 2811 - Divide Bandwidth

We have Cisco 2811 router with on serial interface and four fast ethernets. We planned to take 10 mbps Internet leased line and we have to divide it into two parts. For one network is should be 6 Mbps and the rest bandwidth for another network. Can any help in this Software/Hardware used: cisco...

How can i telnet to a cisco 1700 series from a remote host

Hello can anybody tell me  How i can telnet to a cisco 1700 series from a remote site.? Software/Hardware used: Cisco 1700

how can we configure a 36 port router?

how to install, configure and use a cisco 36 port router? Software/Hardware used: cisco 36 port router

how to delete router configuration

I have 2800 router and i tried to delete the all old configuration but its not deleted,any idea about this problem Software/Hardware used: hardware

VPN Pass-Through Cisco 871

Hi All, I'm trying to setup VPN pass-through on a Cisco 871 router.  I have to admit, I'm not very knowledgeable on VPN, let alone doing it on a Cisco router.  I referenced a Cisco document building this config, but can't seem to get it to work. Here's where I am currently at:  I can access...

how to configure PA-MC-STM1 card in cisco 7206 router

I want to know how to configure PA-MC-STM1  card in cisco 7206 router Software/Hardware used: Cisco 7206 Router

RIP Protocol

I need to enable RIP on R1 & R2 to route for 192.168.1.0/24, on R2 configure default route to forward unknown destinations to ISP, on R2 propagate the default route to R1, on ISP configure a single static route the 192.168.1.0/24 network pointing to R2, configure RIP so that the routing updates are...

wireless roaming howto

I have 3 routers (2 trendnet, dlink) one of trendnet (192.168.100) is connected to my proxy server and i want the other 2 acts as access point and do roaming. I did a setup using same ssid, differents channels but i can't ping to 192.168.10.100 (proxy connected ). What else should i do? Thanks in...

cisco router 1841

how to install and connect, cisco router 1841 to pc desktop.? how would i know if it is connected.?

Routers

What router component holds routing table, ARP cache, and running config file?

split static ips between different machines

I am on a cable connection wiht a 5port switch and a router (wgr614v7) I have my router attached to the switch pulling a DHCP lease from ISP, which runs the majority of my house), and my server is connected to the switch pulling 5 statics off one of the three nics installed. one nic is disabled,...

Free Chapter - Cisco IOS XR Fundamentals

Another free chapter download is available on the IT Bookworm Blog. Written by: Mobeen Tahir, Mark Ghattas, Dawit Birhanu, Syed Natif Nawaz Book: Cisco IOS XR Fundamentals Overview: "Cisco IOS XR Fundamentals is a systematic, authoritative guide to configuring routers with Cisco IOS XR, the...

network problem

Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router

Configuration for the OEC or Motorola Canopy router

I would like to know how to configure the OEC or Motorola Canopy router. Where can I find this information?

Cisco routing problem

I have a Cisco router (routerA) at a remote site, which connects point-to-point to the HQ site (routerB), and it needs to communicate to another router (routerC) that is connected at the HQ site. From the CLI in routerA I cannot ping routerC, but from a PC located with routerA, I can open a dos...

Cisco Networking

How can we provide load sharing on single router of two ISPs. plz let us suggest on the same.