RAID 0

RAID Configuration in HP Proliant DL360

I just bought an HP Proliant DL360 G6 Server, I have install the HP Smart array and Configure the RAID 0 and 5 with a 5 HDD SAS 147 GB HDD, I installed Window 2003 E.Edition 64bit on RAID 0 but can not see the RAID 5 which should be the other HDD. Can some one show me how to configure it aft OS is...

Windows XP Raid driver 0 install

Is it possible to install the raid driver after you have installed windows xp. I know it says you are suppose to install before loading the OS. Software/Hardware used: Windows XP, Raid

unable to detect HDD with SCSI RAID 0

hi, i have win2k installed on server which gives BOD now, i want to reinstall the server but when i try to boot using windows 2k server bootable CD it gives error as HDD not detected, can anyone pls advise process to install OS on server which has RAID 0 inplace Software/Hardware used: windows...

Logical Partition Windows Server 2003

Hi I am using windows server 2003 standard edition,with three RAID DISKS and I created RAID 0,with capacity totalling to 408 GB,now I want to create a partition.I can't get it right, need help

External Hard Drive Repair

I took apart a LaCie 2TB external hard drive because one of the drives was bad; it was clicking when I turned the hard drive encasement on. It has 4 500 GB hard drives set to RAID 0, and two hard drive controller cards so the hard drives are set in pairs as 1 master and 1 slave. I don't have a...

Raid 0 Migrating - RAID mode in BIOS causes BSOD

I have a Dell xps 420 that came with Vista 32 bit. I have switched over to Vista 64 bit (and as far as I can tell updated all my drivers). I want to run raid 0. I would like to use the Migrating feture and avoid having to do a fresh re-install. The issue I am having is every time I enable raid mode...

Raid 0 Set up internal to external drive

I have a Dell 420xps. It came with a 320gb sata drive. I have added a 500gb "internal" hard drive. I also added a 250gb USB "external" hard drive and a 500gb eSata "external" hard drive. I would like to run raid 0 on the 500gb internal and 500gb external and leave the other 2 as they are. Can this...

Can RAID 0 volume be deleted and re-added with no data loss?

I have a Dell Precision 690 Workstation with an LSI Integrated RAID controller. I have a 2-disk RAID 0 (what LSI refers to as an IS or Integrated Striping) volume. Recently the motherboard was replaced (and the RAID controller is integrated onto the motherboard). Ever since the motherboard...

raid 0 array setup

my new two 500 gb drive system has drive one setup as raid 0 with an indication of C: and D: drives of 250 gbs each and no other drives listed. Where is the other 500 gbs

Boot drive failure, but RAID is okay

I had to replace my boot drive. Reinstalled Win XP. System found all the drives, but I can not access the RAID. BIOS loads the Adaptec 1200 Raid, I guess from the PCI Card. In Device Mgr, it sees two identical drives RAID 0, but I can not access them. What am I doing wrong? How can I get the...

Upgrading Computer Motherboard that currently has two RAID 0 setups

I will be upgrading my computer components with a new motherboard and currently have a RAID-0 setup with my old mb's built-in Promise FastTrak 378 controller. I also have a Promise FastTrak TX4310 pci card controller with another RAID-0 setup. Both have two drives each. Will I lose data on either...

Installing Win2003 Server on a RAID Disk

Can WIN2003 Server be installed on a disk that is part of a RAID 0 or RAID 1 array? I am trying to install Win2003 Server on an IBM eServer series X206. I have two 80 GIG SATA drives attached to a SATA RAID controller and have them both defined as members of the array. I tried both RAID 0 and RAID...