• Deploying VOIP and QOS

    We want to deploy VOIP to our network. We first need to implement QOS how can we do that? We have all HP switches and Cisco routers. The firewall is also a Cisco (PIX).

    Karl Gechlik9,860 pointsBadges:
  • security CheckPoint vs. PIX firewalls

    Dear can any one know which one best technology Checkpoint or PIX?

    Networkfierwall5 pointsBadges:
  • How to block P2P applications in PIX 525 firewall

    I need to know how to block p2p applications using a pix firewall 525

    Yasir Irfan5,535 pointsBadges:
  • Point-to-Point VPN through a NATed ADSL Modem

    Greetings, I am trying to setup a Point-to-point vpn tunnel using the Cisco Pix ASA. Here is the scenario: One location got a ASA connected to a Cable modem which assigns its Public IP (static) address directly to the ASA. On the other Location the other ASA is connected to an ADSL Modem which do...

    Fusionex20 pointsBadges:
  • PIX firewall internet problem

    Hello this is my pix firewall 515E configuration. Password: Type help or '?' for a list of available commands. pixfirewall> en Password: pixfirewall# show runn : Saved : PIX Version 6.3(4) interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1...

    Uzairahmad25 pointsBadges:
  • Which tool is used to configure 50 pix firewall?

    i have 50 pix firewall and how will i configure these firewall.

    Cybersoni5 pointsBadges:
  • Setting up PIX535 but no network connection at all

    I am setting up spare firewall on an old PIX 535. I reset the box to factory default, assign the inside interfact an IP address and use a cross-over cable to for a laptop to connet to PIX.  The problem is I am not able to ping the firewall from the laptop vise versa.  There is no any ACL on the...

    springman95 pointsBadges:
  • Do I have to use proxy with PIX firewall?

    i have pix 515E firewall and cyber roam device which is using as a proxy.do i have to use proxy with pix firewall

    Intrnetworking30 pointsBadges:
  • Cisco ASA5510

    I need to find out if there is a command to shutdown Cisco ASA5510 firewall rather then walking up to the firewall and pulling the power plug ... thanks

    Kwt712555 pointsBadges:
  • Combining Networks with Same IP Scheme, VLAN,

    Hi, We are combining an couple offices next week & i need some advice. The networks already have VLANs set up. we have a Cisco 3550 Layer 3 switch set up to route traffic. The servers are on this site also. The network IP's are 10.1.1.x, 10.1.4.x & 10.1.5.x. Servers reside on all of those networks....

    Ramii5 pointsBadges:
  • Cisco ASA 5510 site-to-site with PIX v6.3

    I've recently developed a need to connect 2 networks together. One network (PIX Network) is currently connected to another network (DOMAIN 1) already via IPSEC site-to-site VPN. The other (ASA) is connected to many other sites via IPSEC site-to-site VPN and is those sites main domain server (DNS,...

    Madpawn220 pointsBadges:
  • How to locally authenticate users using PPTP on a local PIX firewall

    I need to locally authenticate users using Point-to-Point Tunneling Protocol (PPTP) on a local PIX firewall. Once the users have authenticated, I need them to connect to a Windows 2003 server which is hosted at a remote location securely with encryption or some sort of tunnel. I have already got...

    NetworkingATE1,545 pointsBadges:
  • CiscoASA5505 DNS not getting to domain reverse lookup zones.

    We are a state agency with a main office here, then about 45 smaller offices throughout the state. The small 1 person offices connect back here via a web provider (ISP) and VPN client. The rest connect back here using either a Cisco PIX 501 (4 of our older small offices) or a Cisco ASA5505 - and in...

    Shadowspapa5 pointsBadges:
  • Cisco PIX emulator for VMWare?

    Is there any Cisco PIX emulator to work under VMWare? I'd like to build a virtual network identical to the real one, so I could always test in the virtual environment before applying any change to the real one.

    Horus5 pointsBadges:
  • career in security

    i am b.tech graduate 2008 passed out & am CCNA certified and i want to do another certification which is most useful in career PIX or FIREWALL or RHCE AM STILL SEARCHING FOR JOB please answer which is better career choice

    Vamsib410 pointsBadges:
  • Using switch or router ACL to block streaming traffic

    I would like to block streaming media requests using either the LAN switch or the site edge router. The site is on a private network and does not have a local firewall at the edge. Has anyone used Cisco ACL's for this purpose and if so, how did you do it? Or, would I be better implementing a...

    Labnuke9932,960 pointsBadges:
  • hocan we install and configure pix 515E between proxy and modem

    I have to install and configure a pix 515E firewall between the internet and LAN. Our client have 2 Mbps internet connectivity and they have a public IP also. The modem is connected to switch. That switch is connected to the device called CYBERROAM, this device is using as a proxy server. The...

    Intrnetworking30 pointsBadges:
  • Redundant DMZ switch configuration

    I've live DMZ switch (c3750) in production. I'm required to configure redundant DMZ switch (c3750). What precutions do I need to take. To give a bit more information the current DMZ switch is connected to the Primary PIX and Secondary PIX. Number of DMZ servers are of course connected to the...

    Fmubarek15 pointsBadges:
  • Configure PIX to allow access to Remote Web Workplace and Exchange Server on SBS 2003

    We have the following network configuration: Router -------- Outside: Static IP from ISP Inside: IP Address: 10.0.0.1 (Static) DHCP enabled for all other clients Pix ------- Ouside: 10.0.0.2 (DHCP from Router: Resvered) Inside: 192.168.2.254 (Static) Network ---------- 192.168.2.0 255.255.255.0 All...

    KitManSupport5 pointsBadges:
  • pix506e prob

    after basic configuration of pix 506e firewall, when I'm connecting it with pc the lan card icon is showing not connected . i've tried different cables and on different pcs too but showing no result.i'm able to ping e1 from hyperterminal and from command prompt i'm able to ping lan card ip. plz...

    H.b.chayan5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following