1
  • Reasons for using RIP instead of OSPF,EIGRP

    Now a days also why we are using RIP instead of OSPF,EIGRP.Any one knows means please tell me.

    yans112112290 pointsBadges:
  • I want a autofallback of link from BGP to OSPF

    Hi , I have a cisco 1841 router connected to 2 different isp & running 2 different protocol (ospf & bgp). I want to use ospf link as a primary & auto switch to bgp link in case of pri link failure. I have added static route to make ospf link pri  & it works but unable to auto...

    Chandrakant5 pointsBadges:
  • OSPF over a Layer 2 Switch

    Hi I have a really stupid question. I have 2 xLayer 2 switches (Cisco) and two routers connected to those switches. One routing to another network and the other to the internet. I want to setup OSPF to enter routes dynamically. They don't want to pick-up neighbors unless they are directly...

    IanOlivier10 pointsBadges:
  • How can I enable OSPF in Cisco 3560G

    ospf in cisco 3560G

    Santosht5 pointsBadges:
  • SLARP

    In GNS, I manually assigned IP address to the serial links between two routers, and also made two more areas. All of them are running OSPF. When I restarted all the routers, I found out below that some interfaces it is shown as SLARP (using the command #show ip int brief). Does anyone know how this...

    Harrypotterr285 pointsBadges:
  • VLSM routing protocols

    which routing protocols support VLSM

    Libby5 pointsBadges:
  • Configuring OSPF to speed up internal traffic with Cisco 1800?

    How can I configure OSPF to speed up our internal traffic using a Cisco 1800? What information do I need to begin with? Does it need to be installed on all routers? Or just one?

    NewnanIT1,110 pointsBadges:
  • regarding Network

    How can i do practise of all levels if network practicals like ospf, eigrp and bgp, isis, hsrp etc.   I neeed link where i can i get best webside so i cam guide my self.

    Virendra45635 pointsBadges:
  • What happened if I set ip unnumbered fa0/0 in my serial interface and later my fa0/0 went down?

    My question is simple. what happened if I set ip unnumbered fa0/0 in my serial interface and later my fa0/0 goes down. if I establish ospf in that network which interface will proces the hello packet and which interface via send the hello packet ?. load balance ?

    Bibs40 pointsBadges:
  • Can I prevent OSPF from advertising a specific network on an interface

    Is there a way to tell OSPF to not advertise a specific network on a spefic interface without stopping the adverts of other networks? Example Router has 5 interfaces F1 is a link to another router F2 is a link to another router F3 = netB F4 = netC F5 = netD I need nets BCD to be advertised out F1...

    ITKE346,430 pointsBadges:
  • OSPF Routers not Sharing Routing Information

    Ive been trying to configure ospf on my home lab but they do not share routing information. Ive been trying to figure out the problem a week now but yet i cannot solve it.. Please could someone help me.. thanks.. Here is the config of my 3 routers running on frame relay Router1 router ospf 1...

    Swamier065 pointsBadges:
  • OSPF (ASAP)

    Hello  everyone, Here i have problem with my OSPF network problem. I have post  The detail below that explain the configuration i have implemented. THe problem is that i can ping from PC0 or PC1 to the backbone router. but i cannot ping the other side of the area 0. Also i can ping from Router2...

    Jale36535 pointsBadges:
  • OSPF

    what the difference between OSPFv1 OSPFv2 and OSPFv3 ????

    Samz198610 pointsBadges:
  • When do I use RIP, EIGRP, IGRP AND OSPF?

    When do I use RIP, EIGRP, IGRP AND OSPF?

    NetworkingATE1,545 pointsBadges:
  • RIP and OSPF security

    can anybody explain to me the Routing Information Protocols and Open Shortest Path First security....how it works and how does it make sure the protocols is secured....?

    Shafa5 pointsBadges:
  • Connecting data closet switches to the core with redundant links

    I'm moving our flat network which covers a three-story building and about 450 users to a subnetted network. I would like to know about connecting data closet switches to the core with redundant links. Can I implement OSPF on the core and connecting switches and eliminate spanning tree? In this...

    NetworkingATE1,545 pointsBadges:
  • How do you configure load balancing on unequal path with OSPF

    please tell me how to configure load-balance on unequal path with ospf.

    Vinesh123480 pointsBadges:
  • About routing protocol

    Hi Engineers my name is vinod, i would like to no routing protocols ,like how rip,igrp,eigrp,ospf and bgp works and what is advantage and disadvantage of this protocols, specifically what is route poisening. i will appreciate for any kind of answer and any attachment or links will also help me....

    Hacky5 pointsBadges:
  • OSPF Network Types

    Can some one please explain the main differences and importance of OSPF network types?

    The Dream5 pointsBadges:
1

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following