• CCM on 2600xm ?

    I have a 2611xm and a 2620xm and 2 - 7942 IP Phones - Can I install Cisco Call Manager and make one ring the other? How? Which IOS do I need and can you set me in the right direction? I have never installed CCM before... Thanks in advance.

    CCMNewbie5 pointsBadges:
  • Server Remote Management LAN ports

    Are the server remote management LAN ports in servers today mostly 10/100Mb or also 1GbE

    Aprakash10 pointsBadges:
  • 110 block cross connections

    How many times can you cross connect a 110 block

    Jemm5 pointsBadges:
  • Information required on 10Gigabit Ethernet cards

    Hello All, I needed some information and datapoints on the following topics: - today what is 10GbE card used for? - what do you see the future for 10GbE? - what do you think is an acceptable price point for this card (just a guesstimate)? Today it is very expensive as compared to the regular 1GbE...

    Rigveda0 pointsBadges:
  • 10 Gbps Bandwidth

    Do you think we will need bandwidth higher than 10 Gbps in the next 5 years

    Jogale200010 pointsBadges:
  • 10Gbe Interfaces & Connectivity

    It is kind of a complex; i was wondering if it is possible to connect from an XFP-SR 10GBe (LC) Interface to an X2-SR 10GBe (LC) Interfcae

    Vdave5 pointsBadges:
  • How to recover _msdcs zone, when it accidentally deleted?

    Dear Sir/Madam, This is Faisal Rafiq MCSA & MCSE certified, my question is how to recover _msdcs zone, when it accidentally deleted?

    239069370 pointsBadges:
  • WiFi without tie-in deal

    Is it possible to get WiFi access at home without being tied in to a deal?

    mikebeaken5 pointsBadges:
  • Does the D-Link DSL-504T 4 Port ADSL/Modem Router work with a d link modem

    Does the D-Link DSL-504T 4 Port ADSL/Modem Router work with a D-link modem?

    Matt1330 pointsBadges:
  • How can I get rid of the PJL STATUS command from the top of my AS/400 Reports?

    I have just installed an IBM4247-003 printer to our AS400 via LAN connection. Everytime a report is printed, the top of the first page has a PJL command. We currently are on V5R2. I created the device as a Type(3812) Lanattach(*IP) Port(9100) MFRTYPMDL(*IBM4247DUAL) SYSDRVPGM(*IBMPJLDRV). The...

    zbbwoc95 pointsBadges:
  • Internet connection problem

    Since a couple of years I am experiencing a peculiar problem. I use 3g Data card(USB modem ) for my Internet connection. After some time a pop up is displayed in the desk top screen written as " This USB device can perform faster if you connect it to to a high speed USB 2.0 Port". After this...

    Shambhunath5 pointsBadges:
  • How fast does IPv6 run?

    Does the IPv6 protocol perform any faster than the IPv4 protocol? Would there be any need for a network running IPv6 to use an application acceleration or other network performance enhancing device? Does that answer change when an organization is running a dual-stack (both IPv4 and IPv6)...

    SearchEnterpriseWAN1,080 pointsBadges:
  • How do WAN optimizers handle IPv6 traffic?

    What do WAN optimizers do with IPv6 traffic if they can only handle IPv4 traffic? Does the IPv6 traffic just get ignored and not-optimized or does it depend drastically on the vendor's technology?

    SearchEnterpriseWAN1,080 pointsBadges:
  • Requirement to set up a LAN and a WAN

    This is a Civilian emergency services plan a 5 day strike. The existing communication structure can not be used. Therefore I have been tasked to provide CIS support at a number of locations Tasks I need to produce a plan for a LAN to accommodate 50 users and up to an additional 40 if required....

    jeffrb40 pointsBadges:
  • Wireless Access List

    My wireless access list was enabled and no MAC addresses were listed on it, thus no devices can connect to the network. Can I forcefully connect or reset all settings without connecting? I would have to go through a great deal of effort to physically access the router so if that is unnecessary I...

    Insecure508260 pointsBadges:
  • How to make two routes in a single PC by two NIC’s ?

    Hi, I am trying to connect to ISP connection on my PC using two LAN cards. I want to use both connection simultaneously. I want to load balance between these two connections. Is there any way ? I have heard about > netsh , command help line but don't know configure process. 2. Also please tell...

    itaiyebali5 pointsBadges:
  • Static Route for VLAN

    Anyone can help me. I setup 2 VLAN in HP v1910-24g switch. VLAN 1 - 192.168.1.1 & VLAN 2 192.168.8.1. My switch should be gateway for this 2 VLANs. My problem, VLAN 2 unable to access internet which is on vlan1. I can ping router (192,168,1,254) from VLAN 2. Also added a static route in router...

    azlan4365 pointsBadges:
  • Windows 2k3 DNS sometimes does not resolve domain properly.

    I have a rather vague problem. Sometimes, seemingly at random, certain websites become unreachable. Big sites, like Spotify and Facebook spring to mind. When i restart the DNS server on the Domainconoller they "come back up". Or, more accurately put are resolved correctly. What could be the...

    AlphaBootis95 pointsBadges:
  • Streaming satellite tv through Flash media server

    Hi. I have a tv tuner card in my pc which I would like to use to stream satellite channels over IP. I laso have Flash media streaming server installed on another station. I would like to know how I can get a specific channel from this tuner and stream it to FMS so it can broadcast it over the...

    sebouh0025 pointsBadges:
  • I/O bottleneck

    DearI have one FTPS, based on windows server 2003. We use WS_FTP program, which is create a lot PostgreSQL task and also write a lot on I/O. This mainly cause our server halt many times a day and my customer cannot login to our server at server busy time happen.May I know some solution, cause that...

    tombeck45 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following