• Sending UDP packets to a different subnet

    Can UDP broadcast packets be sent to a different subnet through a router? I’m curious because I need to find certain devices on the network, and some of them may be on different subnets.

    ITKE54,720 pointsBadges:
  • Fibre Channel HBAs initiator or target mode for NetApp

    How can you tell if the fibre channel HBAs are in initiator or target mode in a NetApp SAN?

    ITKE54,720 pointsBadges:
  • Adding two addtional SAN switches to the Fabric

    I have an HP eva5000 SAN with 2 controllers and 2 x 16 ports brocade switches - I have purchased two additional 16 port brocade SAN switches - how do I go about adding them to the fabric? Core Edge design maybe?

    Markburse0 pointsBadges:
  • HP Blade SNMP query: Getting individual blade power meeting readings

    Hi: I'm trying to get individual blade power meter readings on a HP Bladesystem c7000 enclosure through SIM. The blades have the correct ILO advanced license. The problem I'm having is finding the correct mib or oid to pull out this data. I've been looking through cpqrack but can't find anything...

    Nictotten5 pointsBadges:
  • Command router EIGRP

    In the command router eigrp 100, what does the value 100 represent?

    michaelsilue5 pointsBadges:
  • System i v6.1 FTP

    I've been receiving data since 2003 with FTP that runs from a CL program. Recently upgraded to a new machine with V6R1 OS/400. Began getting EPSV error message. Added 'SENDEPSV 0' after the 'USER' line. This got rid of the EPSV error message but now get: 227 Entering Passive Mode...

    DKIverson5 pointsBadges:
  • How to code RAW Berkley sockets on TCP/IP?

    How does one create RAW Berkley sockets on TCP/IP? I’ve read a few tutorials, but all seem to be overwritten. I’m looking for the easiest and most straightforward way to do it.

    ITKE54,720 pointsBadges:
  • Configuring VLANs on NetGear FS726T Switch

    I am not a trained network specialist, but I'm installing a network at our church. We have a NetGear FS726T switch and a WG102 access point. We want to have to two VLANs: one to be used by the staff with full access to all of the devices on the network and to the Internet; and the other to be used...

    Krused135 pointsBadges:
  • Port monitoring with HP ProCurve 4104GL

    Having problems configuring a Web filter with a HP ProCurve 4104GL switch. Does this switch support port monitoring? Thanks. Moderator Note: This is a submitted question

    BrentSheets6,875 pointsBadges:
  • IP Addresses of a Linux Application Server

    How can I find the IP addresses of my Linux application server? I’m working in C++. I know the main address, but there will be a few more based on the network and those are the ones I need.

    ITKE54,720 pointsBadges:
  • DHCP Server provides Wrong Subnet

    Our company had a hub and spoke network for years, a single server room supporting 20 remote locations, most using the Citrix farm.  We grew and started a second server room.  At the second location we have a switch stack of 9 Cisco 3750 10/100 switchws setup with 5 VLANS.  previously IP...

    D50041115 pointsBadges:
  • What layer of the TCP/IP would ARP and RARP belong to

    ARP translates Layer 3 addresses to Layer 2 addresses, and knowing fully well that it is not an IP-only or Ethernet-only protocol. Can anyone help with this, it's getting a bit confusing.

    Freshfall5 pointsBadges:
  • Cisco 3500 Switch How to configure

    I've been given a Cisco 3500 XL Switch. Question is what can i do with it? I was hoping to split the ports into VLAN's for a start preparing for CCNA exams. Up to now I've mainly done book work. I want to get my 'hands dirty'. Is this a manageble switch ...? - i dont know. I've tried Consoling into...

    Pelvicthrust170 pointsBadges:
  • What layer of the OSI model does a switch operate?

    At what layer of the OSI model does a switch operate?

    NetworkingATE1,545 pointsBadges:
  • How to connect multiple subnets using RV042 router

    Hi all, I'm trying to figure out a way to get multiple subnets to communicate. Here's the scenario: 2 subnets - 192.168.101.x and 192.168.104.x 1. Router - Linksys RV042. WAN 1 port to internet, LAN port to internal network. Default Gateway with IP of 192.168.101.253. The WAN2/DMZ port is not being...

    Lordhowe175 pointsBadges:
  • How to setup Sonic Wall NSA 3500 as NTP server

    I would like to set the NSA 3500 as the NTP server for internal devices such as switches. The version of code is 5.5.1.3-9o

    Armptech5 pointsBadges:
  • Zebra ZM400 network configuration

    How do change the printers name and IP address from the printers LCD?

    JDamage5 pointsBadges:
  • Trying to detect 3G or Wi-Fi network connection on Android

    Does anyone know if its possible to implement a "PhotoStateListener" to see if the 3G or Wi-Fi network connection has been restored on my Android? I'm currently seeing both LISTEN_DATA_CONNECTION_STATE and LISTEN_DATA_ACTIVITY say cellular in the API summary. Does that mean 3G only? Thanks!

    ITKE54,720 pointsBadges:
  • What’s the best option for network disconnections in software?

    I'm working with a network C++ program in Microsoft Windows that I'm trying to test for network disconnections at various times. Here's what I'm doing so far: Manually disconnecting the network wire Using IPCONFIG / release Using a cports program to close the socket What other options are out there...

    ITKE54,720 pointsBadges:
  • The Partner transaction manager has disabled it support for remote/network transaction (Exception from HRESULT : 0x8004D025)

    Hello.....Every one I have a question that I get the following exception when I connect my application to the remote database and there is no exception when I connect my application to the local database. What is the problem? I also have searched my problem on the Internet and I have found many...

    Ghulamsiddiq5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following