• browsing and mac address

    Im confused. Im working with DSLAMs and i have a question. if one CPE is connected to a DSLAM port and i cannot detect a mac-address on that specific dslam port,does this mean that the modem on the other end is not on sync status? if i see a mac-address on the dslam port, what can i prove?

    Splithorizon5 pointsBadges:
  • How do I use Veritas Volume Manager DMP with a StorageTek ST2540 array

    We have recently aquired a Sun StorageTek ST2540 array and directly attached it to Sun T2000 server. While the native Solaris 10 MPxIO is able to recognize duel path to the Storage but Veritas DMP is unable to. Could this be because of array support missing in Veritas Storage Foundation Suit 5 for...

    Ranger2k75 pointsBadges:
  • HP Open View Storage Data Protector

    We are instituting this new back up device. It was just thrown into my lap and I don't have any idea how to use it. I am struggling through, however, I keep getting a critical error message as follows:Health Check Failed. It then states that I need to check the log files from the CLI. I have tried...

    Talk2tisa0 pointsBadges:
  • SCSI Boot with IDE, old CMOS

    Compaq Deskpro EN 733/512 with Windows 2000 Server booting on 9GB SCSI drive, Adaptec controller. Active Directory, Domain Controller, WINS, file/database server. Drive getting full, Non-Profit on the Cheap, picked up a large IDE drive hoping to simply add it. Life is for learning, now I understand...

    VietBob0 pointsBadges:
  • Cisco switch for iSCSI SAN

    A SearchStorage.com reader recently asked: I was wondering if you could recommend a Cisco switch that can be used for Exchange to SAN (NetApp FAS960C) iSCSI connectivity.

    Andrew Burton355 pointsBadges:
  • Intel ISCSI Remote Boot error message TCP/IP

    Using Windows Server 2003 and get this error when using Intel ISCSI remote boot "ERROR: Could not establish TCP/IP connection with iSCSI target system." Using Pro/1000 server adapters and Dell Poweredge 2900 server

    ITKE413,420 pointsBadges:
  • Hyper-V remote management tools not working over VPN

    When i try and run some Hyper V remote management tools over the VPN (wireless connection) I receive a "Access Denied: Unable to establish communication" error message. Is this an issue with my VPN? or something else

    ITKE413,420 pointsBadges:
  • Virtual Directory

    How to perform operations in IIS without logging in as administrator user. e.g creating virtual directory, assigning permissions to a virtual directory and so on.

    Sim1135 pointsBadges:
  • VMWare vs. Virtual Server 2005

    Hello, I am looking to deploy a virtual environment that can contain multiple machines (50+), have the machines networked inside the virtual environment, and be accessed remotely by two or more simultaneous users. This is primarily going to be used as a training and test environment. So the remote...

    Mcman19835 pointsBadges:
  • What are the most overused tech buzzwords for 2008?

    I'm the editor for whatis.com and I'm trying to put together a list of the most overused tech buzzwords for 2009. Can you help? Cloud is #1 on my list (and all its variations). Green will be on the list too. What else belongs on the list?

    Margaret Rouse20,565 pointsBadges:
  • Port Forwarding with Cisco 3560

    Hi Friends, I have a small requirement. please see my configuration. i have an L3 switch (Cisco 3560) series and now i am forwarding all the traffic from my network to Firewall from L3 switch through this default route " ip route 0.0.0.0 0.0.0.0 10.11.12.2" where 10.11.12.1 is my L3 switch...

    ManDark5 pointsBadges:
  • Is it possible to lift router-based bandwidth caps (if they exist)?

    like the title says, is it possible to lift a router based bandwidth cap (if one exists) on my router. im only pulling about 100kb/s on a DSL line. i dont have a wireless setup running, jus straight cat-5 from the router to my cpu. i would assume capping would be done server side, but someone said...

    Stress5 pointsBadges:
  • 8 port fast ethernet switch

    Can I use it to set up a small LAN Can I use it as a hub in a star network.

    Me123455 pointsBadges:
  • iSCSI SAN how many IP Addresses are needed?

    We are planning to implement an iSCSI SAN. There are 4 controllers, each with 2 iSCSI ports. How many IP addresses are needed for the ISCSI SAN

    ITKE413,420 pointsBadges:
  • Windows 7. What are peoples initial thoughts

    With the release of windows 7 there has been alot of press coverage. I am curious to hear what the community thinks of Windows 7 and any experiences you have had with it. I know MrDenny has posted a few blog entries about it. Share your thoughts and experiences. Thanks Sean

    ITKE413,420 pointsBadges:
  • Server 2008 domain or workgroup?

    Someone set up a server for us as a domain without asking anyone when all we need is a workgroup. What kind of problems could we run into if we demote the server to a workgroup? It if is okay to do, how is it done?

    XMac110 pointsBadges:
  • Vista laptop won’t recognize Window 2000 Server network

    Hello, I'm having a great deal of trouble getting a laptop with Vista Home Premium to recognize our network (and map a network drive). We have Windows 2000 Server here with many XP Pro laptops, but this is the first Vista. I've tried turning off the firewall, disabling antivirus, everything. I have...

    Ed333315 pointsBadges:
  • Connecting 2, 3 or 4 sites over MPLS

    Hi. I have some routing experience but I don't have much experience routing over a service providers MPLS network and had some questions.. Say I had 3 sites in different cities. I want to be able to route my data traffice to each site. I would like to use a MPLS provider. Does the provider hand-off...

    ChicagoTechie5 pointsBadges:
  • AS/400 WebDAV to remote Sharepoint server

    Does anyone have successful experience working on using WebDAV from an AS/400 to a Microsoft SharePoint website? Our developers would like to place content from the AS/400 on the Sharepoint website but they are having lots of issues getting this to work. I am going to look at the network traffic to...

    Labnuke9932,960 pointsBadges:
  • VPN behind PIX firewall

    Hi, I have a PIX firewall and I am trying to make a vpn connection from client machine behind the firewall to a server in another site, with a public IP. I am getting error 800. need help please

    Sabusada5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following