• Cannot connect pc to the internet

    I cannot connect my pc to the internet though it's connected to the network. It was connected all along and suddenly I cannot browse. It tells me page cannot be displaced whenever I try to open any browser. The cables are connected the ip address is correct. I cannot ping the machine from any...

    Carolit5 pointsBadges:
  • Home Network Configuration SQL Express 2005

    Hello, I am pretty new to Sql. I had setup a SQL Express 2005 Advanced on a computer w/ xp on it before and had no problems. I recently purchased a installed a new computer (the other one died) w/ Windows Vista. As before, I downloaded and configured Sql Express per instructions for the software...

    Ddog06295 pointsBadges:
  • Remote Management Via Satellite

    I'm a small ISP. I have approx 40 subscribers. My backhaul is via satellite. The LAN side of the Satellite is Wireless ( Router linked to satellite modem, Wireless access point linked to Router via ethernet, CPE's associate wirelessly with AP and customers PC's are linked to CPE via ethernet.)...

    Oigeboy5 pointsBadges:
  • Lost connection to server 2003 shared drive

    Hi All, We have windows 2003 file server and all our clients have suddenly lost connection to its shared drive. We have checked the permission for this share and all domain users have change and read rights - (network policy). All the other shares on the other servers on the network are ok. It was...

    Cholox5 pointsBadges:
  • Show a peer why spending the extra money for a full duplex RF link is better than half for a WAN bridge

    Where can I find reference material to show a peer why spending the extra money for a full duplex RF link is better than half for a WAN bridge? I have 20+ years of networking experience and this RF guy thinks he knows it all. He has management sold on a cheap solution. I'm not having much luck with...

    NetworkingATE1,545 pointsBadges:
  • VPN User IP Location

    Hello, I am using CISCO VPN. We have users that connect to our company's location using CISCO VPN. 1) Can we find out where they are located. Like what state they are connecting from. Any way to trace this?

    Imran hussain khan5 pointsBadges:
  • V-Lans VS Routers

    To control network traffic when is it better to use V-Lans and when is it better to use Routers? Is the choice dictated by cost or by networking requirements. If so what are the requirements that would merrit V-Lans over routers?

    NetBossUSA5 pointsBadges:
  • need help about patch panel

    i need some advice about patch panel. a). what is it? how does it really works b). do i need it, especially that the company is talking about upgrades? c). how to set it up we have a switch with a lot of ports and some ports are connected to the servers and the others are connected to a lower-port...

    Aaa33320 pointsBadges:
  • Migration of child domains from one Active Directory forest to a different Active Directory forest

    I have been given a project to migrate one child domain abc in a forest called group.local (abc.group.local) to another child domain in completely different forest call xyz.group.local. Since the forest roots of both forests are the same I cannot easily get DNS to resolve in order to create a...

    WinIT ATE110 pointsBadges:
  • accounting package sharing

    currently using Brilliant Accounting package, opened another office about 30km from H/O - how do we go about in sharing same acc. package at same time. Any suggestions?

    Tirsa015 pointsBadges:
  • network topology choice

    which network topology works better for a peer to peer WAN?

    Phelpsie5 pointsBadges:
  • networking

    which command can you use to determine the configuration of your IP setting?

    636842210 pointsBadges:
  • Network-clock-select using four PRI’s.

    I have four AT&T PRI's, two VWIC-2MFT-T1 cards. Is the following config correct? network-clock-participate wic 0 network-clock-participate wic 1 network-clock-select 1 T1 0/0/0 network-clock-select 2 T1 0/0/1 network-clock-select 3 T1 0/1/0 network-clock-select 4 T1 0/1/1 How would you configure...

    Walked285 pointsBadges:
  • Number of routers needed

    How do you determine how many routers you will need for a wireless network?

    ITMSI5 pointsBadges:
  • Using ip helper-address on a vlan with two subnets

    I am trying to get ip helper-address to be able to pull DHCP addresses from a super scope. Right now it will only pull from the subscope that matches the subnet of the primary subnet for the vlan. Does anyone know of a way around this? Or if there would be an adverse affect on the current DHCP...

    Jfenton5 pointsBadges:
  • VPN Setup 2003 Server

    I have one domain server. I tried to set up the RAS VPN service as outlined in Microsoft's Knowledge base. How ever if I get the vpn to work then no one on the internal network can access the internet. I understand they use the same services. Is there a way to configure the RAS for VPN and allow...

    Hsmithdp125 pointsBadges:
  • Servers stopped mapping drives to each other.

    Hello, I was using remote desktop to configure my new server (2003 R2) with routing and remote access. As soon as I hit ok after going through the wizard I lost my connection and could not connect again. After hooking up a monitor and a keyboard and mouse, I logged back on and disabled routing and...

    Tkaltenbach5 pointsBadges:
  • How do I become an ICT professional?

    How do I become an information and communications technologies (ICT) professional?

    NetworkingATE1,545 pointsBadges:
  • FIREWALL Management

    Who should be responsible for the upgrades to the firewall UNIX operating system and the upgrades to the Checkpoint application Network Operations or Information Security?

    Bobbypastrana10 pointsBadges:
  • Query error when using application role with ADO connection

    I am developing an application with an ADO connection. I need to run a query on two different databases on the same server using an application role. When I run the query I get an error \domainusername does not have a logon on database (referring to the second database). Is there any way around it?...

    SQL Server Ask the Experts2,585 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following