• Console Session on cisco router

    Hi                I have two routers in my lab , which  is not accessible via console. one is a cisco 3640 router, it shows some unrecognised characters when accessing via console. i did reset the baud rate jumper ,but no result.               In 2811 router it shows boot up...

    Puli45 pointsBadges:
  • What’s the best certification for a networking career after the CCNA?

    I am a final year student in electrical engineering. I am now working on completing my certification in CCNA. What else is needed for a profession in networking? Should I go for the CCNP and CCIE, MCSE, or RHCE? Please let me know the best way to move towards a networking profession. What should be...

    NetworkingATE1,545 pointsBadges:
  • Related stubs storage domain

    Hello,              Recently i am working stoarge domain.  Our application creates stubs of Host data. Would please tell me what is the need of this stubs and what are the valid cases should test the stubs are working.   Thanks, Bib

    79900150 pointsBadges:
  • Routing Entry&Routing Data

    Which one is important for running a job in subsystem Routing Entry&Routing Data ? (Indetail pls)

    qmaster1,675 pointsBadges:


    VADERA10 pointsBadges:
  • Wireless

    Sir , I have to install a point to point RF link between 2 location wiht the capactiy of E1 or 2E1 . so cud u pls cuggest me what are the best products to install a point to point E1 or 2E1 or 100 Mps capacity for IP Network . Thank you Teh student.

    Ksr1234320 pointsBadges:
  • l2l vpn tunnel

    i have one server which is inside firewall ip address is This server is accessible via l2l vpn to the outside ip  the lan to lan vpn is working tunnel peer ip is my access list is access-list inside-nat0 extended permit ip host

    Ekansh405 pointsBadges:
  • SBS 2003 replacing port hub issue

    I recently replaced an 8 port hub with a 24 port hub on my sbs 2003 network. This connected fine to the server LAN but with no connectivity to the internet - all other workstations showed "Limited or no connectivity" - any ideas what I am doing wrong?

    ITKE1,062,865 pointsBadges:
  • BTS 10200 command definitions

    Are there definitions to the commands on the Cisco BTS 10200 switch whereby I can understand what each command input means

    VOIPEng5 pointsBadges:
  • Trial Software Survey: You could win a $50 Amazon gift card!

    Hey there, we'd love to get your feedback in this survey on trial software downloads. It's an area we're looking at expanding, perhaps even into its own section, and any insights you could provide would be much appreciated. You could even win a $50 Amazon.com gift card for participating:...

    JennyMack4,280 pointsBadges:
  • Community Update: The IT Blog Top 10 for Sept. 10, 2009

    As part of a new feature on the Community Blog, each week we'll be doing a run down of the 10 most popular blog posts over the previous week, in case you were wondering what your peers were reading or a hot topic somehow missed your radar. Still think we missed something? Send me an e-mail at...

    Michael Morisy8,643 pointsBadges:
  • Reliability score

    Does anyone know the reliability score of Windows Mobile 5.0?

    Bpb5 pointsBadges:
  • Windows 2000 server AD

    I have three servers running windows servers 2000 all have lastest SP4.  Two are domain controllers and one is Exchange 2000 server.  I was testing Windows 2008 RC server on one of our PCs and accidently hooked it up to our network and left it on the network for about 6 hrs then I realized it and...

    ITKnowledgeSearch15 pointsBadges:
  • Suggested bandwidth for web conferencing

    Can anyone suggest what bandwidth i need for web conferencing. I want to have 2 webcams set up that everyone can see along with a PPT presentation. Should have around 50 people watching. Also any software recomendations for this? Thanks

    ITKE1,062,865 pointsBadges:
  • Networking cisco access point

    i am working on cisco access point 1242 i had default username cisco and password Cisco but when i deleted and changed a new user name and password xxxx what happen, i can telnet through cli mode with new username and password but when i try to take http access the access point take old password...

    Ekansh405 pointsBadges:
  • Operator Action Required on Device XX

    I have an HP 4015dtn setup as a *LAN printer on our iSeries. Device Class - *LAN Device Type - 3812 Device Model - 1 MFRTYPMDL - *HP 4 and *HP4000 SYSDRVPGM - HPPJLDRV We continually get the Operator Action Required on Device XX (C R) (xx being the name of our dev printer). We have to answer this...

    Christyt15 pointsBadges:
  • Network Access

    i have a network but the problem is that some system's acsess the server shared resources but some time pc cant access the server, wht's the problem behind it

    Netamit5 pointsBadges:
  • connection lose on domain

    One of our newer domains is having a problem with connection to mapped drives, server, internet, and shared printer connection lose. Once the connection is dropped it will not re-sync or reconnect to mapped drives ect... untill a full reboot is done. We've not done much in the way of changing any...

    Madpawn220 pointsBadges:
  • what does occupancy mean in a network

    what does occupancy mean in a network

    Jtmbox200310 pointsBadges:
  • SNMPv3 Configuration with HP OV

    I am trying to configure snmpv3 using HP OV on a cisco router. The router has been configured properly to run snmpv3 already. I then edited the mgr.cnf file on the server located at /etc/srconf/mgr to add the following entry: usmUserEntry "agentEngineID" snmpv3user usmHMACMD5AuthProtocol...

    Phrathepmali30 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.