• Multiple Networks

    Hi, I'm a bit new to networking... I'd like to ask for for from you guys out there... I want to set up 3 networks for our school - 2 in the computer lab and 1 in the office... However, I'd like that to assign 192.168.1.x to Lab1, 192.168.2.x to Lab2 and 192.168.3.x to the office for easy management...

    SirJhun5 pointsBadges:
  • How can I disable browsing from my 2960 switch?

    Can I disable browsing option on my 2960 switch for protecting from some users. What command I can use for this?

    Intrnetworking30 pointsBadges:
  • Copper T1

    Can I breakdown a T-1 circuit that has 20 Centrex lines assigned to and punch down each line on a RJ21x jack?

    Mfjohnson5 pointsBadges:
  • How to setup wireless Internet access on 2 desktop PCs

    I have 2 desktop pc's in my home and I'm not sure what I need to get internet connection on both without running cables accross the floor. I have DSL through my phone company and I think I need 2 wireless cards and a router but I don't know what kind or if that's even correct.

    Rochellebarth15 pointsBadges:
  • After earning a CCNA, which certification is best for job security?

    I am currently getting my CCNA and would like to do one of the Cisco professional courses after. Which one would you recommend in terms of job security and money? I have been told CCVP is a good option, but I am not sure.

    NetworkingATE1,545 pointsBadges:
  • XenDesktop load balancing

    I have 3 XenDesktop DDC servers and want to load balance and prefer not to use MSFT NLB. Has anyone used anything else?

    ITKE341,745 pointsBadges:
  • XenServer on Hitachi BladeSymphony 320

    I have installed XenServer on a blade inside a Hitachi BladeSymphony 320. The issue i have is that it doesnt recognize the FC HBA Any suggestions

    ITKE341,745 pointsBadges:
  • Tracking Laptop Users

    Does anyone have a recommendation for a good software program to track internet content for lap top users when not connected to the network? Specifically, what software does the best tracking when the users connects back to the network.

    Gamrey5 pointsBadges:
  • Designing a network

    A user recently asked this question via e-mail: I want to design a network, the specification is given below. Can you help me in this regard. Specification are 1) We have 7 site. 2) Each site have about 250 user and site one have 500 users 3) Exchange server, Mail server should be located at main...

    ITKE341,745 pointsBadges:
  • FTP over SSH on Windows

    Has anyone ever set up a Windows server for FTP over SSH? The FTP server I use is Gene6 (hosts over 100 user accounts). If you have not used that particular FTP server application, which one do you use and why? Thanks!

    Labnuke9932,960 pointsBadges:
  • Domino R6 & Crystal Reports 11 for reporting on the web

    Hi, We have a requirement where in we have to generate reports on the web i.e. using I.E 6.x using Crystal Reports 11. The foll are the requirements. 1) Reports i.e. mainly graphs like Pie,Bar, Combo etc are to be created and displayed on the web. 2) The data would reside in Domino databases. 3)...

    VikiLingeria0 pointsBadges:
  • Bladecenter ESX server Vlan problem

    Hello, The bladecenter was initially setup by a company and allows me to only create VM's from Vlan 2. The issue is that I am out of Ip's in that vlan and I wanted the ability to use another address space for the VM's. I've already created a new vlan 20. Here is the current config of the switch....

    Gillron5 pointsBadges:
  • Emulating bad blocks on a VM

    A user recently submitted this question via e-mail: I need to test some crypto utilities on a VM; does anyone know how I could emulate bad blocks? I know it’s possible to hook up a device via USB and connect it that way, but I’d like to see if there is a way I could specify bad blocks right on...

    ITKE341,745 pointsBadges:
  • Avaya 4610SW VoIP Quality Issue – connecting to Cisco Gear

    I have had a 5 User - Avaya Long Ongoing, IP Phone quality Issue that connects to a Cisco POE 3560 switch and a 1841 router with a Full T1. No one can figure out the Poor Quality Issue and Pin Point where its coming from. What would be a Good Tool to use to try an Pinpoint - Findout as to what the...

    DNelson5 pointsBadges:
  • getting started in security

    Hi there! I just have a quick question(or so I thought! I want to get into the IT field and more to the point, into the security field. I was looking at getting a ccna to start then a ccsp next,but is that the most efficient way to go about it? if not then what is a good route to take? Also I may...

    Jman25 pointsBadges:
  • Entire Network option is disabled

    I want to create a shortcut to Entire Network through pointing File Name. Because all the default location to Entire Network is disable. And i also does not want to enable this from Registry. Waiting for quick reply. Thanks in advance.

    Kelp115 pointsBadges:
  • What certifications would help me switch from network engineering to administrator?

    I have two years of experience as a technical support analyst for Elsevier employees where we had access to Elsevier servers through Citrix Metaframe. I worked on Active Directory in creating accounts (Mail and File) on Windows Server 2003. I have an engineering background. I have not had any...

    NetworkingATE1,545 pointsBadges:
  • Best IT solution for Home working

    Hi. Is citrix based solution the best for remote working by employees in terms of information security.Are there any solutions which offer better infosec protection especially to prevent copying of data from screen shots

    Viswanathan65 pointsBadges:
  • Track USER of Computer online who is using max. Bandwidth in lacal area connection

    Hi All, I am sandeep and working at one software company as system admninstrator. company has 60 user (computer) . we have 2 mb lise line . it go through cisco router. and all computer default gatway ip is the router ip. we have ISA server . Now i want to online moniter this network that which...

    Kapadane105 pointsBadges:
  • Cross Domain Solutions

    I have write a task statement for a contractor to develop a cross domain solution. I know what a CDS is but where can I find the basics on how they are developed?

    SeaDog5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following