Maintaining my license
Hello, and welcome to ITKE. Almost any of the Cisco exams that start with the number 642- will re-certify your CCNP. If you look on the Cisco certification tracker it will list all of these, which include some of the wireless exams, as well as many others. With only just over a month to go, [...]
View Answer
| February 13, 2013 8:31 PM
CCNP, Certifications
Hello, and welcome to ITKE. Almost any of the Cisco exams that start with the number 642- will re-certify your CCNP. If you look on the Cisco certification tracker it will list all of these, which include some of the wireless exams, as well as many others. With only just over a month to go, [...]
View Answer
| February 13, 2013 8:31 PM
CCNP, Certifications
How to run a Wi-Fi router without NAT and DHCP
Log on to your wifi router via web browser and disable the DHCP server. This way the wifi router will only act as an access point. Don’t forget to change the wifi router in the same ip address range like other network device.
View Answer
| February 9, 2013 6:18 PM
DHCP, Wi-Fi, Wi-Fi router
Log on to your wifi router via web browser and disable the DHCP server. This way the wifi router will only act as an access point. Don’t forget to change the wifi router in the same ip address range like other network device.
View Answer
| February 9, 2013 6:18 PM
DHCP, Wi-Fi, Wi-Fi router
Hub and Spoke Network
Hello and welcome to ITKE. Separation is perfectly possible with careful design, of the security, and the use of VLANs to keep the traffic from each company only available to users within that company. They can even share the same Internet access, again with careful configuration of the firewall/Internet router.
View Answer
| February 26, 2013 5:04 PM
Networking, Networking hardware, SDN
Hello and welcome to ITKE. Separation is perfectly possible with careful design, of the security, and the use of VLANs to keep the traffic from each company only available to users within that company. They can even share the same Internet access, again with careful configuration of the firewall/Internet router.
View Answer
| February 26, 2013 5:04 PM
Networking, Networking hardware, SDN
Merge two ASA 5510′s into one
Hi, and welcome to ITKE. I will try to help, but without seeing the actual config, this is a bit of an impossible question to answer with any real accuracy. I don’t think it would be a good idea to post the configs here either. Generally, you need to take the parts of the config, [...]
View Answer
| February 5, 2013 1:57 PM
Cisco, Cisco ASA, Cisco ASA 5510, Firewall, VPN
Hi, and welcome to ITKE. I will try to help, but without seeing the actual config, this is a bit of an impossible question to answer with any real accuracy. I don’t think it would be a good idea to post the configs here either. Generally, you need to take the parts of the config, [...]
View Answer
| February 5, 2013 1:57 PM
Cisco, Cisco ASA, Cisco ASA 5510, Firewall, VPN
How to identify a rogue IP in the network
Hi, and welcome to ITKE. It is easy for any device to have a fixed IP address, just by configuration of the network parameters. My guess is that someone brought in a device with a fixed IP address, connected it to your network, and that is how you saw this. That device is probably now [...]
View Answer
| February 5, 2013 12:50 PM
IP address, Network
Hi, and welcome to ITKE. It is easy for any device to have a fixed IP address, just by configuration of the network parameters. My guess is that someone brought in a device with a fixed IP address, connected it to your network, and that is how you saw this. That device is probably now [...]
View Answer
| February 5, 2013 12:50 PM
IP address, Network
Hubs
Not much really happens except you are running it through another port. Does not make much sense to do something like this, but, nothing bad happens. INCORRECT – Really BAD things happen. Most HUBS allow this to happen, as they auto-crossover these days, but as they are not switches, they do not run spanning tree, [...]
View Answer
| January 28, 2013 3:21 PM
Hubs, Networking
Not much really happens except you are running it through another port. Does not make much sense to do something like this, but, nothing bad happens. INCORRECT – Really BAD things happen. Most HUBS allow this to happen, as they auto-crossover these days, but as they are not switches, they do not run spanning tree, [...]
View Answer
| January 28, 2013 3:21 PM
Hubs, Networking
Cisco 3700 config file
From the limited information provided, I presume that your ISP router has an IP address of 98.113.33.13 , you should remove the existing default route, and change the route to use the address of the ISP router. Use the following commands to do this no ip route 0.0.0.0 0.0.0.0 FastEthernet0/0 ip route 0.0.0.0 0.0.0.0 98.113.33.13 [...]
View Answer
| January 25, 2013 5:20 PM
Cisco 3700, Cisco Configuration
From the limited information provided, I presume that your ISP router has an IP address of 98.113.33.13 , you should remove the existing default route, and change the route to use the address of the ISP router. Use the following commands to do this no ip route 0.0.0.0 0.0.0.0 FastEthernet0/0 ip route 0.0.0.0 0.0.0.0 98.113.33.13 [...]
View Answer
| January 25, 2013 5:20 PM
Cisco 3700, Cisco Configuration
Wireless connecton when computer sleeps
If you are using windows 7, then you can change the power plan settings in control panel. Using this option you can set the number of hours after which your computer can sleep, or not to sleep at all. For more info on changing power plan settings: http://windows.microsoft.com/en-US/windows7/Sleep-and-hibernation-frequently-asked-questions#
View Answer
| January 21, 2013 6:11 AM
Wireless, Wireless connection
If you are using windows 7, then you can change the power plan settings in control panel. Using this option you can set the number of hours after which your computer can sleep, or not to sleep at all. For more info on changing power plan settings: http://windows.microsoft.com/en-US/windows7/Sleep-and-hibernation-frequently-asked-questions#
View Answer
| January 21, 2013 6:11 AM
Wireless, Wireless connection
Networking Problem
The usual reason for the Wi-Fi dropping is that it is set to automatically find a free channel. When it ‘sees’ another Wi-Fi router on the same channel, it will change, and drop all the existing connections. Configure the wireless access point with a fixed channel. Only choose channels 1,6 or 11, but also confirm [...]
View Answer
| January 19, 2013 11:44 PM
LAN to WAN Connectivity
The usual reason for the Wi-Fi dropping is that it is set to automatically find a free channel. When it ‘sees’ another Wi-Fi router on the same channel, it will change, and drop all the existing connections. Configure the wireless access point with a fixed channel. Only choose channels 1,6 or 11, but also confirm [...]
View Answer
| January 19, 2013 11:44 PM
LAN to WAN Connectivity
How to connect two subnets and two isp’s with Cisco RV042G
Your ping tests tell you that your routes are working fine. You don’t need to worry about the RV042G configuration as that seems to be configured perfectly. Name resolution is in your DNS settings. On your DNS server in LAN1, you should create a new Forward lookup zone for the domain name for LAN2 and [...]
View Answer
| January 18, 2013 7:44 PM
Cisco router, Subnets
Your ping tests tell you that your routes are working fine. You don’t need to worry about the RV042G configuration as that seems to be configured perfectly. Name resolution is in your DNS settings. On your DNS server in LAN1, you should create a new Forward lookup zone for the domain name for LAN2 and [...]
View Answer
| January 18, 2013 7:44 PM
Cisco router, Subnets
cisco ASA 5510′s setup two firewalls, one for VPN only the other for VPN tunnel and internet
I suspect that all you need to do is add a route into your network for the subnet allocated to the VPN users. You can do this on the fast Internet ASA, but will also need to put this on the MPLS router, and/or other routers in your network or via a routing protocol if [...]
View Answer
| January 22, 2013 6:39 PM
ASA, VPN
I suspect that all you need to do is add a route into your network for the subnet allocated to the VPN users. You can do this on the fast Internet ASA, but will also need to put this on the MPLS router, and/or other routers in your network or via a routing protocol if [...]
View Answer
| January 22, 2013 6:39 PM
ASA, VPN
I found old E00000 log files
Hi, It is advised to keep these files.E0000 are basically transaction log files that helps to recover the to the point where failure occurs. You can check the log files at the location: %ALLUSERSPROFILE%Application DataRed GateLogs Admin Console and Outlook Add-in log files can be found at : %USERPROFILE%Local SettingsApplication DataRed GateLogs
View Answer
| February 14, 2013 4:04 PM
Log files, Microsoft Exchange
Hi, It is advised to keep these files.E0000 are basically transaction log files that helps to recover the to the point where failure occurs. You can check the log files at the location: %ALLUSERSPROFILE%Application DataRed GateLogs Admin Console and Outlook Add-in log files can be found at : %USERPROFILE%Local SettingsApplication DataRed GateLogs
View Answer
| February 14, 2013 4:04 PM
Log files, Microsoft Exchange
RIP, OSPF and EIGRP in same network
Simple answer. RIP doesn’t learn route of OSPF or EIGRP and vice versa. Router 1 doesnt know te route Router 2 subnet. So Router 1 discard the packet.
View Answer
| January 18, 2013 5:11 PM
Cisco, Cisco router
Simple answer. RIP doesn’t learn route of OSPF or EIGRP and vice versa. Router 1 doesnt know te route Router 2 subnet. So Router 1 discard the packet.
View Answer
| January 18, 2013 5:11 PM
Cisco, Cisco router
“ip http secure-server ” command is not available
When you’re in global config mode, you should have the option to enable the ” ip http secure-server ” command. If you’re not seeing it, the only one reason that comes to mind of why it would be gone, is if you’re using different views for different users that have been assigned certain privileged level and may [...]
View Answer
| January 10, 2013 11:40 AM
Cisco 2801, Cisco router
When you’re in global config mode, you should have the option to enable the ” ip http secure-server ” command. If you’re not seeing it, the only one reason that comes to mind of why it would be gone, is if you’re using different views for different users that have been assigned certain privileged level and may [...]
View Answer
| January 10, 2013 11:40 AM
Cisco 2801, Cisco router
Please,can anyone tell me the apparatus for networking
Often I use ping and tracert command. When to solved slow network I use fortigate for define traffic and control my network. You can try fortigateVM.
View Answer
| January 7, 2013 9:41 AM
Networking
Often I use ping and tracert command. When to solved slow network I use fortigate for define traffic and control my network. You can try fortigateVM.
View Answer
| January 7, 2013 9:41 AM
Networking
After CCNA what type of jobs are found?
The degree you have would help you get high pay jobs and help you atain managerial positions but with the CCNA you can also be heading into the telecommunication companies…
View Answer
| January 8, 2013 2:03 PM
CCNA, CCNA Certification
The degree you have would help you get high pay jobs and help you atain managerial positions but with the CCNA you can also be heading into the telecommunication companies…
View Answer
| January 8, 2013 2:03 PM
CCNA, CCNA Certification
Where all the places we use Layer 2 and Layer3 Switches
Thanks for coming to ITKE. Since you have asked more of a general question, I suggest you do a simple google search and you will find more that enough information to answer this question. If then, you still have a specific question, please come back and ask it.
View Answer
| December 31, 2012 3:22 PM
Layer 2 switches, Layer 3 switches
Thanks for coming to ITKE. Since you have asked more of a general question, I suggest you do a simple google search and you will find more that enough information to answer this question. If then, you still have a specific question, please come back and ask it.
View Answer
| December 31, 2012 3:22 PM
Layer 2 switches, Layer 3 switches
Internet access
More information is required to know the exact root cause. Anyway, you can do the following, assuming you are on Windows 7 OS. 1. At System Tray, right click on Network icon and click troubleshoot problems. This will not do a miracle but will find some issues and suggest remedies. 2. Open a command prompt [...]
View Answer
| December 28, 2012 6:35 PM
Internet access, Internet connection
More information is required to know the exact root cause. Anyway, you can do the following, assuming you are on Windows 7 OS. 1. At System Tray, right click on Network icon and click troubleshoot problems. This will not do a miracle but will find some issues and suggest remedies. 2. Open a command prompt [...]
View Answer
| December 28, 2012 6:35 PM
Internet access, Internet connection
How to find the IP address of the system from which user had logged in
For logged on Users: Wrkcfgsts *dev then display For Signed Off users: use devdscr. API Hassan
View Answer
| December 30, 2012 8:01 AM
AS/400, AS/400 Server, IP address
For logged on Users: Wrkcfgsts *dev then display For Signed Off users: use devdscr. API Hassan
View Answer
| December 30, 2012 8:01 AM
AS/400, AS/400 Server, IP address
