• Network Paranioa

    I have WEP enabled on my wireless router. However, I have a small 4 port firewall that I want to use in addition to wireless router firewall and my software based firewall. Is this doable?

    Roblhicks5 pointsBadges:
  • How can I load balance my router managed by two ISPs?

    I have two ISP (Internet Service Providers). How can I balance the load between them (or load balance them) using the router and take their output and send it through one Ethernet port, out to my network? It must be set up  this way because I have only one firewall (which has only one Ethernet...

    NetworkingATE1,545 pointsBadges:
  • Where to connect NAS devices in business networks for storage access?

    In my small business network I have an ISP modem, then a Sonicwall NSA 240 firewall, and then a Linksys WAP 2000 access point (AP). Can I install a network access storage (NAS) device, like a D-Link DNS-343, to the network for all employees to share, store and back up files? And if so, where in the...

    NetworkingATE1,545 pointsBadges:
  • Setting up PIX535 but no network connection at all

    I am setting up spare firewall on an old PIX 535. I reset the box to factory default, assign the inside interfact an IP address and use a cross-over cable to for a laptop to connet to PIX.  The problem is I am not able to ping the firewall from the laptop vise versa.  There is no any ACL on the...

    springman95 pointsBadges:
  • Should I register a DNS name for the NAT IP address?

    I have setup our firewall to NAT the inside IPs to an external IP address. Is there a reason I should or should not register this NAT IP address to a DNS name?

    springman95 pointsBadges:
  • Advanced firewall design

    suggest me some techniques regarding to the firewall design

    Asu30 pointsBadges:
  • Juniper SSG550 Firewall – Routing Policy

    It's required to create a new (virtual) interface (with a global IP) that will receive hits and route them to a specific IP behind the INside interface. So basically a policy or route that will do: 1- User opens browser for www.test.com 2- DNS registered to point to our global IP on the new VIP on...

    TaherAfridi5 pointsBadges:
  • Wireless Network Bypassing

    hi i have one wireless Linksys usb network adaptor , i connect it to my Laptop after getting signal internet start normally .know question is that i want to use my laptop as a wireless repeater .( like attach one router to laptop and getting signal in my place) actually in my room there is very...

    Danial370 pointsBadges:
  • Windows hour glass and black screen during an RTP session

    I get the windows hour glass and black screen during an RTP connection session, after some time of keyboard or mouse inactivity. I move the mouse and the display comes back immediately. On the rmote and host computers I have screen savers off, displays always on, and no hibernate. Any ideas on how...

    Johnnyt335 pointsBadges:
  • Prerequisites for Spiceworks

    What are the prerequisites for installing Spiceworks on our network? What type of account do I need to give it for scanning? Is it safe? How can I audit what the application is really doing for review?

    ITKE361,740 pointsBadges:
  • How to configure a single ethernet port

    how to configur singal ethernet port i want that steps with key

    Afraz5 pointsBadges:
  • 2010 Office sync with PDA

    I'm upgrading Office 2003 to Office 2010. Before I install 2010 Office Professional Pro for XP service pack 3, I need to know will it be a compatible sync with PDA Ipaq x2400 series with Windows 5.0

    LibertyMD5 pointsBadges:
  • Best practices involving admin rights for user on user system

    We are currently in the middle of figuring out the approach we are going to take in regard to a user having admin rights on their system. Typcially we set up a new user as an administrator on their system when they are logged into the domain. They don't have a local admin account on the system,...

    Kevins740 pointsBadges:
  • Windows Server connectivity to local user

    I HAVE TIRED MANY TO CONNECT A USER TO DOMAIN BUT UNABLE TO CONNECT. I HAVE INSTALL ADS,DHCP,DNS SERVER... BUT THEN TO UNABLE TO CONNECT. PLS TELL WHAT ALL I NEED TO CHAECK ...THE ERROR THAT OCCURS IS THAT THERE IS SOME PROM INDNS SERVER CONFIG. PLS TELL ME STEP BY STEP PROCEDURE TO CONNECT THE...

    49932210 pointsBadges:
  • Benefits of VLANs?

    What are virtual lans or vlans? What are they used for and will they allow me to increase my networks overall speed and throughput ratio?

    ITKE361,740 pointsBadges:
  • How can I configure a connection by pppoe on a Cisco 2600 Router?

    please can somebody help me to find out the way i can configure a connection by pppoe on a Cisco 2600 Router?

    T8sta5 pointsBadges:
  • Has any one used trafficsqueezer?

    Hi there, I was looking to do some testing with trafficsqueezer (http://www.trafficsqueezer.org/Doc_FAQ.html) It's an open source network accelerator and before I start testing just wondered if anyone had used it and had experience or if it actually works? Cheers Rick

    RickC495 pointsBadges:
  • Is Outlook Connector a Security Threat to Exchange?

    I'm a chemical engineer working for a small mid-west company (300 - 400 people).  I'm an IT guy at heart from my IT support days in college where I was doing PC repair, setting up small LAN's and troubleshooting server issues.  I installed Outlook Connector on my Desktop at work so I see my...

    ChemEngr5 pointsBadges:
  • Trying to run remote command to view AS/400 UNC and failing!

    I need some ideas here...I'm stuck. I'm running an RPG program that builds some CSV files for our accounting department. Because they love Excel, I had to make it so that the program breaks the data up into separate CSV files so as not to exceed 65,535 rows. Anyway, I am saving the stream files...

    Koohiisan5,020 pointsBadges:
  • TCP1A77 error

    Hi, i do update my OS40 to V6.1 but since i have problem with my STRTCPSVR command when my system is in restricted stat. i got all the time the msgid TCP1A77 (TCP1A77 STRTCPSVR completed successfully; however errors occurred) so my backup counld't start without activiting manually the IP interface...

    junioras400250 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following