• how to connect two Cisco Catalyst 4503 core switches

    i have two 4503 core switch and would like to make redundent

    Mothana55295 pointsBadges:
  • Windows Vista Ultimate 64 bit VPN To Work Network?

    Hi Guys, I just found the hard way that Cisco doesnt have 64 bit VPN Client. i googled a bit came up short.....every search was going towards install XP with Dual Boot and Use XP for work. I need your help in setting VPN using Vista's Network Setup. Start -> Connect To -> Setup a Connection...

    Prashant Pathak5 pointsBadges:
  • Second NIC card won’t stay connected

    I came in this morning to find my file server down. Must have had a power outage over the week end. It's connected to a UPS that was also down. I found DNS Client was disabled on the server. I set it to Automatic. I have 2 NIC cards but now for some reason I can only have 1 endabled at a time. I am...

    Giftbox145 pointsBadges:
  • wants google chat block windows server 2003 domain controller

    I wanted to block Google charting and Google talk without interruption gmail site. could you please help me. I have domain controller installed 2003 server  and using routing and remote access for internet sharing for client PC. Thanks for help

    Hirachilwal25 pointsBadges:
  • Can I prevent OSPF from advertising a specific network on an interface

    Is there a way to tell OSPF to not advertise a specific network on a spefic interface without stopping the adverts of other networks? Example Router has 5 interfaces F1 is a link to another router F2 is a link to another router F3 = netB F4 = netC F5 = netD I need nets BCD to be advertised out F1...

    ITKE351,965 pointsBadges:
  • routine of network security engineer

    what are the daily routine of a network security engineer in a compney, form morning to evening?

    Ssssingh10 pointsBadges:
  • Transmition Security Control in Connect:Direct

    What is the Transmition Security Control that uses "Connect:Direct" ?

    Menkar5 pointsBadges:
  • Pims Support ?

    i was wondering if there is any pims accounting software support here , i have a client using pims but its too slow when two pc's or three are connected , but the network is fine , ping and everythin is good with network , any suggestion please ? ?   thanks

    Mayssam96150 pointsBadges:
  • Bandwidth-controlling

    I have Fiber link for 6 MB with 2921-Router. I wan to segreegate bandwidth 4/2 for 2 Different Department. I have also 2 Catalyst 3750 switch for each department. I need to fix bandwidth 4/2 with access list. Please give me the solution?

    NetworkBandwidth30 pointsBadges:
  • What’s my IP range?

    I am needing to find my IP range and find an avail IP within that range. IP addy - 192.168.1.104 Subnet Mask - 255.255.255.0 Default Gateway- 192.168.1.1

    Techrecruit15 pointsBadges:
  • Obtaining IP address in Xen

    After finally got XEN working, the part I've been struggling the most with is finding a way to get XM to report the IP address of the virtual machine it started up. The VM was in DHCP mode. I'm guessing I could find this out using dhcpd logs (by looking up the mac address), but I'm not sure if...

    ITKE351,965 pointsBadges:
  • Network Design Questionnaire

    I am a student I have a project which a program to design a local area network to a single building. I want to know the questions that I will bring to the user and used in the questionnaire

    A1988ns15 pointsBadges:
  • TCP/IP properties

    tell me about IP address, Subnet mask, Default geteway, preferred DNS server, Alternate DNS server

    Biknet5 pointsBadges:
  • VLAN Configuration help, 3com 4500 26port

    [u3:p][/u3:p] Create vlansAdd ports to vlansSet port 1 as trunk and also added as tagged to all vlans At port 1 i connect my adsl modem router (dhcp enabled). 4500 switch gets 192.168.1.100 as it's ip but all other computers can't get their ip by the dhcp if they are connected via 4500...

    Makrib5 pointsBadges:
  • Configure BIND – How to Configure BIND to respond to a DNS Status Query message?

    I have a device which is attempting to send DNS Status Query messages (opcode=2) to my bind DNS server.  The DNS server is responding with NOTIMP.  Is there a way to configure bind to respond positively to this query?

    Bindadmin5 pointsBadges:
  • Need to know equipment needed to setup a simple network to share DB

    Hello, I am not into networking but I like to try new things. I am setting up a simple network of about 12 computers to share an access database. The site is remote so there is no internet access at this time. We should however have internet access ina few months. I need a list of the...

    Jerbro5 pointsBadges:
  • Cisco MIB Configuration Change, SNMP

    Hello all. How can one alter or hide a serial number through MIB configuration? I'm doing a discovery on a network but my reports find that the serial numbers are actually building locations in that state. And if the MIB config can be changed, what would be the command line? Thanks in advance for...

    Jay249690 pointsBadges:
  • Are additional protocols added to a protocol suite to complete the layers or is a suite cover all of the layers?

    Are additional protocols added to a protocol suite to complete the layers or is a suite cover all of the layers?

    Twittars5 pointsBadges:
  • FOG, DHCP from a Cisco 5510 ASA

    Hey, I am trying to set up fog to be able to image computers on my network. We previously had it set up working properly through a dedicated windows DHCP server, but recently we implemented changes and are now providing DHCP through a cisco 5510 ASA. It was working by itself without any...

    Tlarz5 pointsBadges:
  • How to inform web site visitors that we have added a shorter domain name for easier access.

    What is the best way to introduce a shorter domain name that is just forwarded to the existing web site?  The existing domain name will remain the same, I would appreciate some suggestions how to inform our visitors they can now type in a shorter domain name that is based around the theme of the...

    Waltstoy15 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following