• patch cable or drop cable length

    how do we calculate max length of drop cable used in ethernet lan.

    Vishal15 pointsBadges:
  • Which is more valuable Degree or Certifications??

    Hello Everybody, I am Varun. I am doing a diploma in Advanced Networking and system security from CDAC. I have done BCA. Now, I am bit worried in deciding that in which direction I should move. Should I go for Cisco certification or MCA. Getting more and more certification is enough or is it...

    V200945 pointsBadges:
  • AP MAC filter as ACL from database

    We have 14 CISCO AIR AP 1242 APs around campus. We would like to do : Have a ACL with MAC address allow from our database or XLS sheet and deny others. I already create all the wireless devices MAC address in xls sheet in place. We are trying to do is: Setup ACL for every APs not locally but...

    CHENS265 pointsBadges:
  • Routing scalability issue?

    What's the routing scalability issue with the Internet? Does IPv6 fix it?

    SearchEnterpriseWAN1,080 pointsBadges:
  • Nat on cisco router

    Hi. i have 2 cisco router which they are connected to each other for VoIP. my question is i want to forward all the data from port 80 to be forward on one pc inside the network. can you please help me on this?

    Azrahedour15 pointsBadges:
  • Load Balancing of Unequal Ethernet Bandwidth

    Is it possible to aggregate and then load balance the unequal ethernet circuits like so: I have two ethenet circuits on my Cisco router. Both have equal costs to the next hop. Ethernet Circuit #1- 200M Ethernet Circuit #2 - 100M Can I aggregate both ethernet circuits so that the total amount of...

    Hcandy5 pointsBadges:
  • how to use parallel port for serial communication

    i want to use parallel port for spi. i dont know how to set phase and polarity for sclk.how to send and recieve data. do i need to shift data synchronized with the clock or the parallel port will do it automatically?

    Amna10 pointsBadges:
  • ip not working

    when i replaced the localhost with my ip address, it showed errror. what I need to do?

    Dipakkp15 pointsBadges:
  • how to connect two Cisco Catalyst 4503 core switches

    i have two 4503 core switch and would like to make redundent

    Mothana55295 pointsBadges:
  • Windows Vista Ultimate 64 bit VPN To Work Network?

    Hi Guys, I just found the hard way that Cisco doesnt have 64 bit VPN Client. i googled a bit came up short.....every search was going towards install XP with Dual Boot and Use XP for work. I need your help in setting VPN using Vista's Network Setup. Start -> Connect To -> Setup a Connection...

    Prashant Pathak5 pointsBadges:
  • Second NIC card won’t stay connected

    I came in this morning to find my file server down. Must have had a power outage over the week end. It's connected to a UPS that was also down. I found DNS Client was disabled on the server. I set it to Automatic. I have 2 NIC cards but now for some reason I can only have 1 endabled at a time. I am...

    Giftbox145 pointsBadges:
  • wants google chat block windows server 2003 domain controller

    I wanted to block Google charting and Google talk without interruption gmail site. could you please help me. I have domain controller installed 2003 server  and using routing and remote access for internet sharing for client PC. Thanks for help

    Hirachilwal25 pointsBadges:
  • Can I prevent OSPF from advertising a specific network on an interface

    Is there a way to tell OSPF to not advertise a specific network on a spefic interface without stopping the adverts of other networks? Example Router has 5 interfaces F1 is a link to another router F2 is a link to another router F3 = netB F4 = netC F5 = netD I need nets BCD to be advertised out F1...

    ITKE347,940 pointsBadges:
  • routine of network security engineer

    what are the daily routine of a network security engineer in a compney, form morning to evening?

    Ssssingh10 pointsBadges:
  • Transmition Security Control in Connect:Direct

    What is the Transmition Security Control that uses "Connect:Direct" ?

    Menkar5 pointsBadges:
  • Pims Support ?

    i was wondering if there is any pims accounting software support here , i have a client using pims but its too slow when two pc's or three are connected , but the network is fine , ping and everythin is good with network , any suggestion please ? ?   thanks

    Mayssam96150 pointsBadges:
  • Bandwidth-controlling

    I have Fiber link for 6 MB with 2921-Router. I wan to segreegate bandwidth 4/2 for 2 Different Department. I have also 2 Catalyst 3750 switch for each department. I need to fix bandwidth 4/2 with access list. Please give me the solution?

    NetworkBandwidth30 pointsBadges:
  • What’s my IP range?

    I am needing to find my IP range and find an avail IP within that range. IP addy - 192.168.1.104 Subnet Mask - 255.255.255.0 Default Gateway- 192.168.1.1

    Techrecruit15 pointsBadges:
  • Obtaining IP address in Xen

    After finally got XEN working, the part I've been struggling the most with is finding a way to get XM to report the IP address of the virtual machine it started up. The VM was in DHCP mode. I'm guessing I could find this out using dhcpd logs (by looking up the mac address), but I'm not sure if...

    ITKE347,940 pointsBadges:
  • Network Design Questionnaire

    I am a student I have a project which a program to design a local area network to a single building. I want to know the questions that I will bring to the user and used in the questionnaire

    A1988ns15 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following