Iseries fails to boot
I have a v5r4 820 model that failed. Error code in display is 284C3203 which pointed to I/O problem for either system board or Disk controller. I replace both and the only way I can get past this error is by using the new disk card with the new RAID memory. The old RAID memory [...]

Answer Question   |  December 5, 2008  3:11 PM
AS/400, AS/400 error messages, Error ID 284C3203, IPL, iSeries, iSeries 820, RAID, Tape drives, V5R4

ENDSYS – IPL
HI, recently my development/test box keeps going down because of sapce problems. ASP2 or ASP3 overflows and this causes the ENDSYS. is there any way to know before hand that now the system will go down? i have cleared everything i could and cant afford a new disk so any suggestions to scrape some more [...]

Answer Question   |  August 10, 2010  12:59 AM
AS/400, AS/400 storage, ENDSYS, IPL, Storage

AS/400 unable to IPL
stop at system reference A6de0255

Answer Question   |  September 30, 2008  3:44 AM
A6de0255, AS/400 errors, AS/400 signon, IPL

CPF9033
Hi, This is regarding deleting of user profile from system.If I run a RCLSTG and IPL, then what will be the impact on the system. is there any disadvantages related to this command. Could you please suggest me what are the steps to be taken to delete the user profile from the system. Regards

Answer Question   |  August 29, 2008  6:49 AM
CPF9033, IPL, RCLSTG

IPL
May I know it is a good idea to IPL the AS/400 system weekly?

Answer Question   |  August 26, 2008  12:49 AM
AS/400, IPL

Error after V5R2 CUM load failure
I loaded a CUM PTF onto a clean install of V5R2 (reason – replaced all disks) I can’t get the PTFs to install as I goofed and installed the Group befor the CUM. I need to restore my OS and start again without reinstalling the Licensed Internal Code. I have a tape backup – how [...]

Answer Question   |  September 8, 2008  8:12 PM
CUM PTFs, IBM, IPL, iSeries, PTFs, V5R2

No Logging
We lost a power supply causing our 820 to crash during dayend processing. The jobd forces logging but we did got only a 1 page joblog when the system came back up with the date/time after the system IPL. Why did I not get a full joblog? It would have allowed us to figure out [...]

Answer Question   |  May 6, 2010  1:32 PM
IPL, iSeries 820, Joblogs

Why stop HTTP *ADMIN server?
During IPL the startup job issues this command: ENDTCPSVR SERVER(*HTTP) HTTPSVR(*ADMIN). The comment says this is for security purposes. Is anyone else ending HTTP *ADMIN server at IPL. Is this security over kill?

Answer Question   |  June 20, 2008  10:19 PM
AS/400 Web servers, ENDTCPSVR, HTTP, HTTPSVR, IPL, iSeries

Error after V5R2 Cum PTF load….
On Friday evening I loaded the latest Cum PTF’s for V5R2. The box IPL’d without any problems and all the PTF’s were “Temporarily applied”. However, after a second IPL yesterday (scheduled weekly IPL) it failed and the screen SRC read B0006 1406. Has anyone any idea what this could be? The IBM reference manual states [...]

Answer Question   |  April 27, 2010  7:32 AM
AS/400, IBM, IPL, iSeries, PTFs, V5R2

iSeries crashes when saving to save file
Hi, We’ve come across a problem when we save to a *SAVF on our iSeries. We use the save to save files a lot on our system and it’s always worked fine. In the last few weeks however, the system has crashed twice (with an immediately re-IPL after abnormal system end) when saving to save [...]

Answer Question   |  June 4, 2008  9:23 AM
AS/400, Crash, IPL, iSeries, SAVF, V5R4

How to findout iseries AS/400 server’s IPL status?
How to findout iseries AS/400 server’s IPL status?

Answer Question   |  February 21, 2010  12:50 PM
AS/400, IPL, iSeries

ipl;
how to setup automatic ipl

Answer Question   |  May 20, 2011  3:33 PM
IPL