• iSeries unattended IPL with LPAR

    I am using BRMS for our full system backups and use the option in BRMS to IPL the system upon completion. Does the unattended IPL with restart shut down both LPARs gracefully and restart them normally? Our startup program was not modified when the additional partition was set up.

    abat9940 pointsBadges:
  • after IPL the server is slow for hours

    I have Iseries , and after it finish count from 1 to 48, a black empty screen stayed for about 30 minutes .. and after it start working the server always become very very slow for about 3 hours ... is there any solution to that

    abar1425 pointsBadges:
  • Errors during an IPL

    during an IPL we received B200F001 LP=002. What is this error

    Gurias5 pointsBadges:
  • V5R2 console issue

    Restored a full save to an 820 which had an OPS console. Worked all the way until the final IPL. LWS controller is now not detected. How do I resolve this? Resource        Type  Status                Text CMB01           284C  Operational           Combined function IOP Card...

    expson35 pointsBadges:
  • z/OS IPL stops

    I am trying to IPL a new z/os isolated LPAR.  The IPL starts up okay until I get to the point where the MASTER address is suppose to start up. It just halts with no messages or wait state codes.

    Easygoing5 pointsBadges:
  • LPAR IPL

    If we do an *FULL IPL on Logical partition will initiates/includes hardwares also?

    Explorer1910240 pointsBadges:
  • Question on changing status of iSeries IP address

         How do you change the status of IP address in iSeries from ACTIVE to INACTIVE after performing IPL? I need to know the procedure on doing this because In our scheduled DRP testing activity, there's a part in that activity where i have to configure an existing Production IP address for...

    danmd5systemad370 pointsBadges:
  • QSTRUP

    Hi friends, I have the "JDEdwards Enterprise 1" on my system AS/400, and evertime after the IPL I execute this process by STRQSH. How can I configure this "runs" on my QSTRUP ?, I don´t know if this parameters below is correct; CALL PGM(QWAS6/QWASSTRSVR) PARM('-profilePath'...

    RBDSILVA540 pointsBadges:
  • ipl;

    how to setup automatic ipl

    Rfoster010 pointsBadges:
  • Partial DST

    What is Partial DST? and how do we do it with out putting system in Manual mode?   AS/400,iSeries

    qmaster1,675 pointsBadges:
  • ENDSYS – IPL

    HI, recently my development/test box keeps going down because of sapce problems. ASP2 or ASP3 overflows and this causes the ENDSYS. is there any way to know before hand that now the system will go down? i have cleared everything i could and cant afford a new disk so any suggestions to scrape some...

    Rockleadme385 pointsBadges:
  • IPL (boot) from SAN

    I have 2 System i 570 connected to 2 x DS8100 in 2 different locations and replicating with PPRC. No internal disks, IPL from SAN. We will run a switch test : stop production server, end PPRC and start backup server on the "PPRC copy" (more steps indeed). Does anyone has information about the...

    BillyBelgium190 pointsBadges:
  • No Logging

    We lost a power supply causing our 820 to crash during dayend processing. The jobd forces logging but we did got only a 1 page joblog when the system came back up with the date/time after the system IPL. Why did I not get a full joblog? It would have allowed us to figure out where processing...

    RCOMSTOCK25 pointsBadges:
  • Error after V5R2 Cum PTF load….

    On Friday evening I loaded the latest Cum PTF's for V5R2. The box IPL'd without any problems and all the PTF's were "Temporarily applied". However, after a second IPL yesterday (scheduled weekly IPL) it failed and the screen SRC read B0006 1406. Has anyone any idea what this could be? The IBM...

    Selectsoft65 pointsBadges:
  • PWRDWNSYS,IPL,AS 400

    Hi, In a situation, where operator issued PWRDWNSYS with out his/her knowledge..Being system admin how can i stop the Process of IPL? What would be the better thing to stop it. Regards -Qmaster  

    qmaster1,675 pointsBadges:
  • How to findout iseries AS/400 server’s IPL status?

    How to findout iseries AS/400 server's IPL status?

    Iseries servers0 pointsBadges:
  • SRC code at IPL on 9406 170

    When trying to IPL an As400 9406 170 i am getting SRC code 10112541 almost immediately - this is probably a hardware issue - but i cant find this code in the manual or on the web - does anybody know what this SRC code means

    Teckgeck170 pointsBadges:
  • IPL through SST

    for sxapmle i have 3 LAPR's, one is primary and two secondary.my question is it possible to make an IPL on individual LPAR's separately thorough SST in manual and normal mode.and when we need to go for an IPL in manual mode..please give me a brief notes..thanks in advance

    0 pointsBadges:
  • ipl details

    is it possible to IPL for individual LPAR or its related only for total server?

    0 pointsBadges:
  • as400 ipl

    I need the as400 to automatically start tcpip at IPL. How do I make this happen?

    Siscomputerspecialists45 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following