Hello, I had an issue like all the LPARs were down and I can only access the frame through Web based HMC. Is there any way to find the OS level through this interface? Thanks.
Answer Question | January 28, 2013 8:01 AM
AS/400, HMC, OS/400
How to clear event logs using v7.7.4 SP1 would like command line information
Answer Question | March 17, 2012 5:58 PM
HMC, HMC Event logs
Hi When i tried to connect my iSeries Hmc Console,I’m getting ”0043 Connected – waiting for screen data”,Now,I don’t have access to the box.I have submitted a FULLSYSTEM backup in restricted mode,while it was in progress,my console got disconnected ang getting the above said message while getting in. How can i get in to the system [...]
Answer Question | March 17, 2012 8:33 AM
AS/400, Console, HMC, iSeries
How to check the ATL logs and HMC logs? ? Is there any commands to verify directly ?
Answer Question | October 18, 2011 8:04 AM
AS/400 backup, ATL & HMC As400, ATL & HMC logs, Automated Tape Library, HMC
I’m at the planning stage of this upgrade and it’s the first upgrade with a HMC attached. There’s no twinaxial console, so my question is , Can the HMC perform the upgrade? Do I need to attach a console, to carry out the upgrade.
Answer Question | April 13, 2011 10:06 AM
HMC, HMC updates, OS/400 Upgrades, V5R3M0, V5R4M0
Can you go directly from V6.1.2 to V7.3.5?
Answer Question | December 31, 2010 8:57 PM
HMC, HMC updates, iSeries
Can anyone point me to some good information about upgrading an HMC? I am getting ready to perform my first of many HMC upgrades and would like to be able to review the documewntation and get some pointers concerning upgrading from a release below V6.1.3 to V7.3.4.
Answer Question | December 31, 2010 9:24 PM
HMC, HMC updates, HMC V7.3.4, iSeries
How can I possibly know if an iSeries model 825 has proper service processor to support HMC?
Answer Question | December 16, 2010 8:12 PM
AS/400, HMC, IBM iSeries 825, iSeries, V5R4
Hello There. I’m trying to connect to the outside world but my eth port is connected to my power 7 box. Is there a way to ‘share or split’ this port ? Either thru some kind of swithch or software that somehow would create a lan console ? I’m trying to make what I have [...]
Answer Question | November 6, 2010 7:20 PM
Ethernet connection, Ethernet Ports, HMC
Just i have configured HMC on my Iseries 520 model…..can you send the details for LPAR configuration?
Answer Question | June 1, 2011 11:36 AM
HMC, iSeries 520, LPAR Configuration
I need some assistance. I have a large iseries that has an issues with the Interactive Indicator on Startup. let me explain, When the system is started out of restricted state a program is called. While comming up the Interactive light or the “X” is present indicating the interactive session is running. However, if a [...]
Answer Question | April 9, 2010 3:31 AM
5250 session, Client Access, HMC, Startup
Hi, I am trying to connect to HMC using client access.On the configure PC5250 screen I use the following: a Update the System Name to the HMC host name or TCP/IP address. b Set the port number to 2300. c Press the Properties button. The properties button will launch the Connection dialog shown below. Do [...]
Answer Question | February 12, 2010 1:38 AM
HMC, HMC V7R3
We have a 9406-570 that has four partitions. This system was originally setup without an HMC. Each of the partitions had the Service Agent program enabled to call home for any hardware error. Now they have installed an HMC to manage the 570. We have disabled the Service Agent, according to IBM’s website. GO SERVICE [...]
Answer Question | October 15, 2009 7:45 PM
AS/400, HMC, V5R3
In HMC SCREEN there is a message numbers ’4341 & 4325../ what is the meaning of no?
Answer Question | September 14, 2009 6:23 AM
Is HMC requeired to work with partitions using SST (STRSST) option 5 ?
Answer Question | August 28, 2009 7:17 AM
On the HMC of our 9408-M25 V5R4, the 5250 display is DSP02. In the past, I’m almost positive that it was DSP01. Two questions: 1) will it being DSP02 (running in QCTL) cause any problems for a BRMS system backup (restricted state)? 2) is there a way to get this back to DSP01?
Answer Question | August 13, 2009 5:33 PM
AS/400 Display File, DSP01, DSP02, HMC, PC5250, V5R4
Dear All As we know we r using AS400 520 Server with OS V5r4mo .We wnt to Use Latest HMC ,which hmc will Best to use ,as we can install hmc application on windows pc, if yes than what will be he configuartion of wondows pc or its require additional hardware to do so …………,or [...]
Answer Question | July 28, 2009 10:07 AM
I am unable to login to HMC as i forgot the password. Is there any way to reset the password?
Answer Question | May 30, 2011 2:47 PM
AS/400 login, AS/400 passwords, HMC
Using basic IBM public command to getupgfiles from restricted shell (putty.exe) adn getting error for invalid ID/password.
Answer Question | June 16, 2009 12:46 PM
HMC, HMC Shell Commands, Unix, Unix shells
I have recently upgraded my HMC to V7.3.4 and WEBSm is no longer supported on this level. Remote access is now via HTTP. Has anyone set this up and if so, can you provide a link to any documentation? I’ve searched the IBM sites but not been able to find anything as yet. Many thanks [...]
Answer Question | March 16, 2009 12:01 PM
HMC, HMC V7.3.4, HTTP access