• Running gigabit over cat5e?

    What happens if we run gigabit over cat5e? Will we get a connection? Is it reliable? What would be my max possible speed?

    NewnanIT1,110 pointsBadges:
  • Simultaneous ethernet and wireless on Windows 7

    I'm trying to connect a printer that can only use a ethernet connection (directly wired from printer to computer). But when I plug in the ethernet then it turns off my wireless connection to the internet. How can I plug in my printer without it turning off my wireless connection to the internet?...

    Avongal5 pointsBadges:
  • leased Line with public IP’s

    i have a lease line with Huwaei SmartAX unit ,The ethernet interface directly connected to the firewall.The public IP's  assigned for this lease line not reaching the firewall after ISP .Is it compusory have a Router to have public IP's .

    Leolink5 pointsBadges:
  • Ethernet Cable Run Max Length

    What is the maximum cable length we can run from the switch to the desktop? What about from the patch panel to the switch to the desktop? Using cat 6? Is it different with cat 5 or 5e?

    Karl Gechlik9,860 pointsBadges:
  • What cable needs to be run for Ethernet?

    We want to run gigabit Ethernet. Should we use cat5e or cat6? What is the difference between the two? Should we pick one over the other?

    Karl Gechlik9,860 pointsBadges:
  • Figure out length of ethernet runs after the fact

    How can I asses how long my Ethernet runs are to the jacks at a users desk? Is there a software or hardware tool we can use to figure this out?

    Karl Gechlik9,860 pointsBadges:
  • Bridging or bonding ethernet & firewalls from separate carriers

    We have two 10 MBit internet connections. They are both Ethernet handoffs and enter two different sonicwall firewalls. Is there a way to bridge or bond these two separate lines? They are from two separate carriers and have separate IP ranges.

    Troubleshooter24755 pointsBadges:
  • Network Connection Freezes

    For some reason, at random, among 20 PCs on my network, in the morning or during the day, the network connection stops responding for both intranet and internet communications. The only solution thus far is to remove the NIC from the Device Manager, reboot the PC, and let Windows XP Pro find the...

    DboiSOBE0 pointsBadges:
  • Layer 2 Ethernet throughput

    We have 2 sites. Point A and point B. Point A has a 100M ethernet line on a 100M port and point B has a logically 20M line seating on a 100M port. Telco providers use traffic shaping to logically set the bandwidth on their L2 device at their nearest office from point B. We have multiple circuits...

    Lynjay5 pointsBadges:
  • How to configure a single ethernet port

    how to configur singal ethernet port i want that steps with key

    Afraz5 pointsBadges:
  • Ethernet Over Copper

    I am thinking of replacing our SDSL line for a EOC 3x3. What sorts of hardware does implementing EOC require. For example T-1 requires a CSU/DSU.

    Jsuarez145 pointsBadges:
  • Ethernet and Patch Cables

    What's the difference between Ethernet cable and Patch cable? And what does "straight-through" mean? Thanks

    123456300 pointsBadges:
  • Is there a difference between Ethernet WAN and Wide Area Ethernet?

    Is there a difference between Ethernet WAN and Wide Area Ethernet? If not, are there other terms people use to describe a high-speed wide area network (WAN) service that uses Ethernet connectivity? Thanks!

    SearchEnterpriseWAN1,085 pointsBadges:
  • Gigabit Ethernet only connecting at 100mb

    Have a Gigabyte GAIp1000 pro board running latest Intel Pro 1000 driver. Added new nic neither will connect at 1000 ony 100 mb on seperate switch any ideas?

    TomKnox40 pointsBadges:
  • patch cable or drop cable length

    how do we calculate max length of drop cable used in ethernet lan.

    Vishal15 pointsBadges:
  • Load Balancing of Unequal Ethernet Bandwidth

    Is it possible to aggregate and then load balance the unequal ethernet circuits like so: I have two ethenet circuits on my Cisco router. Both have equal costs to the next hop. Ethernet Circuit #1- 200M Ethernet Circuit #2 - 100M Can I aggregate both ethernet circuits so that the total amount of...

    Hcandy5 pointsBadges:
  • routing between subnets.

    I have a machine with two eth cards. one is 192.168.1.254, the other 0.254. my gw is 192.168.1.1. I was to make the default gw for my 0/x (eth0) network the 192.168.1.254 (eth1) network. Can this be done?

    ITKE352,380 pointsBadges:
  • Security concerns around .11n Networking?

    I've heard a lot of conflicting reports around whether .11n actually is much more secure than its .11x brethren. Any first-hand experience in starting to deploy it,and any tips on whether I can rest easier at night with it over a Ethernet getup?

    ITKE352,380 pointsBadges:
  • Initialization of ethernet

    I am new in this technology. I am working on ethernet interface with lpc2378.I want to initialize the ethernet block or lpc 2378. Can you provide the flow chart for this.

    RahulsB5 pointsBadges:
  • network design for 3 different companies in one building

    Hi, I have a task to make a proposal on designing a network for 3 different companies sharing the same building floor with seprate file and print server. The network will be on base of 1Gb/s Ethernet and Wi-Fi. What is the best solution for bring those companies into one network share and keep...

    Mustang7135 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following