• Remove Load Source from IBM Power6

    Hi everyone, We have an IBM Power6(8203-E4A) server. It is then connected to two (2) 5886 disk enclosure. Upon scratch install, we can't initialize all disks from the disk enclosure. Because it has been configured before as the load source. Is there anyway we can remove the disk to the previous...

    excellentrandy1,265 pointsBadges:
  • Advice for moving a data center

    I’m preparing for a data center move. What are the pitfalls I need to avoid and what current technologies would be best for a new data center?

  • AS/400 Clutter

    Does anyone know what causes *SQLPKG objects to be created in various libraries by many different users, some by IBM internal most not. Trying to cleanup system.

    Jpolep5 pointsBadges:
  • Best method labeling guide to Ethernet cabling

    Is there a labeling guide to Ethernet cabling? I am researching the best method for labeling cable from one rack of equipment to another and am looking for a standard.

    NetworkingATE1,545 pointsBadges:
  • Building a Data Center from the ground up

    In working with Construction PMs, what can an IT PM bring to the table for a project to build a data center from the ground up?

    Cybrown10 pointsBadges:
  • Adding a node in Oracle 10g

    How can a third node be added in Oracle 10g standard edition? Server being used is DELL 2850.

    Akansha150 pointsBadges:
  • FM-200 sub floor or above floor in the data center

    We are planning on installing a fire suppression system in our data center and was curious if anyone has had experiences using FM-200 in the sub floor and above floor. Thanks

    ITKE350,935 pointsBadges:
  • Following Oracle WebLogic Server as a career

    Would following Oracle WebLogic Server turn into a good career?

    rajeshpvg265 pointsBadges:
  • event id 41 in windows 2008 r2

    I have a HP DL380G6 with Windows 2008 R2 installed. It randomly reboots and when you check the event logs it says - kernel power /event id 41. Already updated firmware, proliant support pack, and system programmable logic device to the latest version but still problem persists.

    Mandosols25 pointsBadges:
  • FM-200 for server room

    How do I pipe size for FM 200 as per standard BS/NFPA?

    Faruk5 pointsBadges:
  • Blocking cell phone activity or wireless broadband cards from within our server room

    Is it possible to block cell phone activity or wireless broadband cards from being able to function within our server room to prevent data theft? Is there a way to capture what they are trying to send? Can I have activity set off an alarm?

    ITKE350,935 pointsBadges:
  • Looking for a driver for a Linotype-Hell Topaz Scanner

    This is a follow up (of sorts) to this question The fine people at the Apple store referred to my old Mac as "vintage" - translation - they can't fix it. So I went to plan "B". I installed a PCI SCSI card in a WIN XP machine. The computer recognized and loaded drivers for the card. I then connected...

    Flame14,925 pointsBadges:
  • Data Center Standards

    We are establishing a new Data Center, is there any standard for Data Center? If so where can I get any sample documentation for establishing a new Data Center.

    Yasir Irfan5,545 pointsBadges:
  • Best way to do the DASD history capture…(Disk usage)

    Dear team, I need to enhance our current system that captures the disk space usage. I need to maintain the history over it. Currently we do it by using DSPOBJD and DSPFD commands and write the details of all objects and files used in the whole system to the outfile. Hardly it takes more than 4...

    Ezhilkumaran0 pointsBadges:
  • Enterprise Monitoring Solution

    Hi All, I'm researching to see what my fellow IT peers are using for monitoring their infrastructure either a global solution or a piece meal setup. Let me know your ideas.

    Aguacer08,135 pointsBadges:
  • CPU Hours and MIPS

    How do you convert CPU hours into MIPS?

    DLLE10 pointsBadges:
  • Install Windows XP in Dell PowerEdge 2850

    I need required install Windows XP sp2 in PowerEdge 2850?

    CAO5 pointsBadges:
  • Career change: programming to networking

    I'm looking to move from programming to network administration and eventually security. I need advice. I have an AA degree. I did tech support and programming part-time in college. Since then, I've spent 2.5 years as a programmer (with some IDS responsibilities), 1.5 years doing QA on niche-market...

    Unicityd30 pointsBadges:
  • ESX 3.5 Networking on IBM BladeCenter E

    I'm looking for suggestions on the best way to configure failover networking using 4 Cisco IGESM switches in the 4 bays. Currently, I have all 4 ports on each switch configured for GEC, but if a switch fails, there is no failover to one of the other switches. Switch1 is for Service Console, Switch2...

    EFStruttin5 pointsBadges:
  • Sessions conflict between Unix NDM server and Windows NDM server

    Hi, I am sending files to Unix NDM server from Windows NDM server. I have a copy command to transfer files. Everything was working fine until recently I had to send some other files to different destination path on the same server. My both scripts trigger at the same time which submit the processes...

    NDMUSER122035 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following