IT Answers » CLI

Progressive Variable: How to write a loop in a batch script

Techy1984 — Mon, 24 Jan 2011 16:08:26 +0000

I have written a batch script that the 7-zip CLI for Windows to split a file into volumes and send it to me via sendEmail.

The issue I have run into is how to write a loop that inputs a new variable for each volume without knowing how many volumes there will be.

For example; 7-zip creates MYFILE.7z.001 then *.002, *.003, etc.

I need to be able to change the last 3-digit extension to the next interval until there is no more to grab. Something like when ‘if exist’ fails, terminate the loop. Any suggestions?

Thank you.

CLI config confirmation

Yeahboy — Sun, 18 Oct 2009 01:54:25 +0000

Hi, does anyone know if d-link is manufactured by cisco? There is this client that asked me on how to create multiple ip adresses on a single interface of cisco router, but the switch connected to it was a d-link switch. Of course, the solution was intervlan routing but I haven’t seen a d-link CLI configuration so I’m not sure on what to suggest. Is cisco CLI the same with d-link CLI? Are the commands the same?

VPN SITE TO SITE CONFIGURATION

RENCE01 — Tue, 25 Aug 2009 09:15:02 +0000

This is my first time to configure site to site vpn from ASA5510:116.93.65.34 -Host-to REmote Cisco 2811-41.204.36.150 (LAN-IP Start at 172.16.16.0-172.16.19.254 subnet mask-255.255.252.0)

Note: Already done configruation on ASA5510 but need to start configure on cisco2811 but i dont know the cli and where to start

Just configure site to site VPN under ASA5510 and having configuration as listed-

IKE Authentication-preshared Key,

IKE Proposal-pre-shared-3des-sha,IPsec

proposal-ESP-3DES-SHA,

CryptoMap Entry-enable,

NAT-T-Enable,

IKENegotiation Mode-Main,

Group Policy-Enable,

Please help me on how i can configure via CLI to Cisco 2811 since not

familiar on CLI and i will be glad if you someone can guide me on how to do it in 2811 so my

site can do site to site VPN. Please help me needed badly…thanks and appreciate your help

Lope

ESX vSwitch command line question

Pharcyde — Fri, 31 Jul 2009 15:24:39 +0000

Is there a command line way of increasing a vSwitch port count?

what is this cli response “&&”

Bahlezi — Mon, 27 Jul 2009 11:46:45 +0000

from the CLI of a juniper firewall, when I ping an IP address, I get this response “&&”. what does this mean?

network problem

Krishnabthapa — Sun, 28 Jun 2009 06:54:13 +0000

Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router

Using SQL CLI APIs to call an sql stored procedure on an AS400

I5DB2DBA — Fri, 26 Sep 2008 19:55:18 +0000

I would like to know if there any examples of using the SQL CLI APIs in a COBOL/400 program that may help me in using the APIs to call a stored procedure and process the result set(s) .

Thanks
Mike

CLI

J4 — Thu, 26 Jun 2008 10:29:29 +0000

what is CLI?

how to write telnet script

Lazythegreat — Mon, 21 Jan 2008 09:25:02 +0000

I need to perform routine router administration from an Linux pc. How can I create a script to logon and perform some CLI automatically?