• Voice and Data Network Setup

    I have two ISP's. One strictly for Voice data and the other is strictly for Data.  I have about 40 users with 40 7961G Cisco IP Phones.  I have one Cisco 48 port POE switch, and I have two Gateways (one for each ISP). How do I setup a network that will: 1. have all the voice traffic go over the...

    Arshad1605 pointsBadges:
  • Cisco 3825 Router

    Can cisco 3825 router support 45mbps link?

    Network Infrastructure5 pointsBadges:
  • CCM on 2600xm ?

    I have a 2611xm and a 2620xm and 2 - 7942 IP Phones - Can I install Cisco Call Manager and make one ring the other? How? Which IOS do I need and can you set me in the right direction? I have never installed CCM before... Thanks in advance.

    CCMNewbie5 pointsBadges:
  • Configuring CISCO 1841

    Hi, I have Cisco Router 1841 set up with this connection: PC1 --> Router 1841 --> NTU --> ISDN Network --> NTU --> Router 1841 --> PC2. I already configured the IP address in the router and want to know how to configure ISDN protocol in the router in order to get full ISDN network...

    gangnam5 pointsBadges:
  • Design the logical lan topology

    given an IP 201.165.201.0 design an IP adressing scheme that satisfies the following requirements; Subnet A, Subnet B

    theciscostudent10 pointsBadges:
  • Associates and Cisco

    I am pursuing my associates in networking in college. When I'm done, I will prepare for the Cisco certification (CCNA). Am I going to be able to get an entry level job, even though I don't have any experience? By the way, what's the entry level salary?

    Peruvian5 pointsBadges:
  • Wireless LAN Logical design

    • Three main groups: Sales, Production and Engineering. Each group has 60 users in each group. • The standard network card is a Cisco Aironet 350, and the access point selected is a Cisco Aironet 1200. • The Sales and Production departments should not be able to access the Web server on any...

    Jonigooner115 pointsBadges:
  • Cisco 2811 – 3 VLAN

    I have a Cisco 2811 Router with 3VLANs. I reset the router from scratch and want to set up my EtherSwitch with 16 ports to have 3 VLANS. Ports 1-10 to be VLAN1, 11-14 to be VLAN2, and 14-16 to be VLAN3. The Gig port will be for my hardware firewall that then goes to my modem. So: Modem -> HW...

    SomEntity5 pointsBadges:
  • How do I setup an automated VPN connection?

    Our branch office uses Cisco VPN to connect to our corporate office - and our corporate office uses Check Point VPN to connect to our branch office. Can I have an automated VPN connection while being at either location? Thanks.

    NetworkingATE1,545 pointsBadges:
  • cisco 2811 with 2 fast ethernet ports and 4 vlans-2

    I need urgent help on this. I have a brand new cisco 2811 with 2 FE ports. The port f0/0 is connected to the internet and the f0/1 will be connected to the switch which has 4 vlans configured on it. I have no idea how to go about doing this. Can someone please help me with the configuration on the...

    Sarfarazkz0 pointsBadges:
  • Cisco SMB RV180W firmware

    Does anyone know where to get the RV180/RV180W - 1.0.1.9 release? We are running the stock firmware and need the port forwarding fix but I can only seem to find the datasheet.

    Dee1011,035 pointsBadges:
  • I want to upgrade my IOS Router 7507. but min flash IOS new version require 32 M.

    A question submitted on SearchNetworking.com I'm want Upgrade IOS Router 7507. but min flash IOS new version require 32 M. cisco RSP8 (R7000) processor with 262144K/8216K bytes of memory. 46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes). 16384K bytes of Flash internal SIMM (Sector...

    ITKE344,955 pointsBadges:
  • Cisco W1C card and Bad Frame and CRC errors

    I have a Cisco W1C card going to a Verso Netperformer Serial WAN Port..V.35, running Frame Relay protocol. On the Netperformer I see Bad Frame errors with CRC's and Aborts. I alrady changeed the card , it is a dual serial card in a 9360. Could the W1C card be faulty? The cisco doesn't show...

    Billbass0 pointsBadges:
  • access cisco switch 3560

    I have catalyst 3560 i need to configure it ....what is the possible ways to get access to the switch ? with the steps.

    Smsa780 pointsBadges:
  • Cisco 3745 and amd_flash_cmd errors

    I have recieved about 30 Cisco 3745 Routers. I have loaded the 12.3.8.5T Enterprise Plus BIN image on them. Most of them work, but there are a few where the engine boards are bad and some where they work but I am getting amd_flash_cmd errors. I have swapped out the flash memeory and NVRAM. In...

    Eyereadyouremail0 pointsBadges:
  • Who is your current WAN Op vendor? (Sponsored)

    If you're using WAN optimization, which vendor are you using? Silver Peak, Riverbed, Cisco, or another company?

    SilverPeakExpert25 pointsBadges:
  • Cisco Call Manager CSS

    Hi, I'm a beginner with Call Manager 7 and need some help. this is a Hotel in Spain. The Director wants to block all the rooms extensions. when the reception makes the customer check in, I have to change the CSS (calling search space) on the Directory number. CSS Block to CSS Allow. So they can...

    Absolutt5 pointsBadges:
  • Without reboot the server how to scan new LUN from HP24K storage

    After  assign the new lun from HP24k to RHEK5.4 ver server. after reboot only it is showing in fdisk -l  commd output. is it any tool is available or any command except partprobe.  Siraaj

  • Is an MCSE or a CCNP degree more valuable to an employer?

    With the economy the way it is, is it better to have a CCNP (Cisco Certified Network Professional) or MCSE (Microsoft Certified Systems Engineer) certificate? I don't have time to complete both courses and I'm urgently seeking employment.

    NetworkingATE1,545 pointsBadges:
  • Cisco vs HP

    I have read a lot about the debate between Cisco and HP switches. In what use cases does going with the HP product make a lot of sense and how much of Cisco's installed base is realistically at risk? What are the primary factors that sway decision makers one way or the other?

    Gcc5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following