• In VPN Which protocol to be used……??

    Hiiiii everybody..... I am Bala new member of this group I have got one small querry regarding VPN, in my organization i am trying to implement VPN for the remote access, in the bangalore office i wanted to install concentrator Cisco 3015 and in the bombay and pune office i wanted to configure VPN...

    Balasaheb0 pointsBadges:
  • changing trunk protocol on cisco switches

    Anyone who has done a change on trunk protocol in a live 24/7 environment. My main question is if all trunks will go down during the change? The net consist of 7 switches and on one of them is an tftp server from which I hope that I can download the configs needed. If all switches are in a long...

    Stbr050 pointsBadges:
  • dropping connections over private T1 with cisco 1751′s at each end

    I keep dropping connection over a private t1 spanned between two 1751 routers. This is most apparent when I am trying to open large files (especially Access) that are greater than 3mb. One of the routers is configured to also act as a dhcp server. the following are the configurations: STATEST#show...

    MrGee620 pointsBadges:
  • Pix blocks Microsoft Office Communicator

    We are running Cisco VPN (3000 headend) clients (4.7.0) through a Cisco Pix 515 (6.3). Our VPN clients are unable to connect to Windows Live Commnications Server 2005 using Windows Office Communicator. The communication is set for TCP (not TLS). Looking at the PIX logs we see that the initial SIP...

    Stuberman0 pointsBadges:
  • NMAP IN WIRELESS

    Hello, Can any one explain me what is NMAP , how NMAP works and how to use it. Kind Regards, Gopal.

    Breathe0 pointsBadges:
  • Loadsharing between two ISPs

    dear sir, I am looking for a load sharing solution between 2 leased lines for 2 different ISPs the diagram goes lke this: LAN-->Cisco Pix-->Router-->2 leased lines. can load-sharing be done at the router without extra configuration at the providers side? can CEF (cisco express forwarding)...

    SkullyMJ0 pointsBadges:
  • WIRELESS BRIDGES

    Dear Sir's, I have two wireless bridges. Master and Slave which are 800 ft apart and two high gain antennas are attached to these units. I am finding a disconnection problem with these bridges. It works for a while but gets disconnected and after doing powercycle on the slave end the bridge starts...

    Breathe0 pointsBadges:
  • Remote Syslog with MySQL and PHP

    Dear All, i want to set up a Remote Syslog with MySQL and PHP on system with whitebox linux,can some tell me a step by step on how to install and configure this,also the requirement needed to complete the task Regards Edwin

    Eduado0 pointsBadges:
  • Setting Up VLAN across WAN link for Testing

    I am trying to setup a Vlan via a WAN Link. Local End has already 4 VLANs. Remote End doesn't. Remote end needs to access VLAN id 4 via the WAN link. Local Gateway router = Cisco 3660 Remote Gateway Router = Cisco 3660 Local Switch = Cisco 3750 Remote Switch = Cisco 2924 What is the config that...

    Aparian0 pointsBadges:
  • Cisco 7606 Vs. the compitition, Foundry XMR series or other.

    My company is looking to purchase a new router, we are looking at expanding our cable tv division down the road with video/ video on demand and need to upgrade our current router due to bandwidth constraints, my question is does anyone have a different router good or bad. All answers are welcome...

    Dfng200215 pointsBadges:
  • CISCO Switch Configuration for DOS Applications on Netware 5.1 SP7 Server

    Hi, Our network is composed of the following: 1 CISCO 2970 GIGABIT (24 x 10/100/1000) 6 CISCO 2950 SWITCH (24 x 10/100, 2 x 10/100/1000) 1 HP Proliant ML520 G2 Server with 10/100/1000 NIC CAT 5e Cabling HP Workstations with 10/100/1000 NIC with Windows XP SP2 All CISCO 2950 Switches (Gigabit Port)...

    JayCuizon0 pointsBadges:
  • connect Cisco VPN client to Linksys BEFSX41?

    Hi all, I have a need to connect to both Cisco PIXes and Linksys BEFSX41 VPN endpoint firewalls, and would prefer to not have to switch VPN clients. Is it possible to create a VPN tunnel to a BEFSX41 using the Cisco Systems VPN Client software? I'm currently using version 4.6.01.0019. I'm not...

    JonathanSpitfire10 pointsBadges:
  • Stop bit problem: USB to Serial Converter attached to motion controller, unable to set for 7-E-2

    I have three different USB to Serial converters, one of them an isolated converter from B&B. One brand of motion controller I work on uses EVEN parity / 7 data bits / 2 stop bits as its default. I find that none of my converters will work on the controller in this configuration. If I borrow a PC...

    Kfink040 pointsBadges:
  • PIX Filrewall VPN

    I'm in kind of a tight spot as far as network admins go. We have a Cisco router that is controlled by our ISP and the firewall was setup by a third party. We have sites connecting thru VPN to our HQ. Some are static and some are dynamic. We also have a need to have VPN clients connect and look at...

    Vdinenna60 pointsBadges:
  • Upgrade step from win nt and win 2000 to win 2003

    I have windowsNT and window 2000 servers with active directory which i want to upgrade to windows 2003,all servers meet requirement for new vesion.Now can same help me on how to upgrade?what steps should i take

    Eduado0 pointsBadges:
  • slow upload speed with cisco equipment

    I am running with a T-3 coming in through a 515e PIX and a 4506 switch. Download speeds are excelent but the upload speeds are extremely slow. If the cisco equipment is bypassed, the upload speeds are great. I have monitored the CPU of both systems during upload and there is no load. What am I...

    Strayrog0 pointsBadges:
  • layer 2 & layer 3 switch

    Hi All, what is the basic difference between layer 2 & layer 3 switch. how can configure layer 2 & layer3 managable switch

    Psharma11760 pointsBadges:
  • RIP Timers

    Dear all, I am confused on RIP timers. Especially, Hold-Down timer. Can someone de-brief me with an example sceanrio that how each timer in RIP behaves and the co-relate with each other?

    SADnBLUE0 pointsBadges:
  • Problem with Cisco Static nat rules

    Hi you guys, We are currently in the process to replace our firewall with a Cisco pix 515. I?ve set it up in a testing environment in order to make a replica of the network so I can test everything. The way the network is setup right now we use NAT to translate the internet ip?s to the internal...

    Vinceke0 pointsBadges:
  • Wireless and VLAN

    Hi, I have the following equipment: - Symbol Spectrum24 11Mbps Access Point (AP-4131) - Cisco 2950 Switch (WS-C2950T-24) Our wireless infrastructure has been active for almost 2yrs now with WEP and Mac Address Security. I wanted to apply more security on our Wireless infrastructure by implementing...

    JayCuizon0 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following