• VPN & CISCO 2610 setup

    Hello Sir/Madam, I cannot access our VPN from the internet outside our organization. I am using Cisco 2610 Router with IOS v12.3. And i created the access-list for the inbound and outbound connections. I have mentioned the access-list below and also i mapped a static IP address with the VPN...

    Parames0 pointsBadges:
  • Checkpoint firewall and Cisco VPN

    Hi all - I have this problem now for 2 separate people and am a little perplexed. Here's what's happening: We have a Checkpoint firewall (Nokia), very restricted access. We have consultants or auditors that come in and need to access their Cisco VPN from inside our firewall and it always fails. I...

    Lirria0 pointsBadges:
  • Strange error message from Cisco 2980 router

    Hi, I'm getting an error message from my Cisco 2980 switch when I type "write mem". The error message is "This command is available only in text configuration mode." I have another identical switch but I don't get an error message when issuing the same command. The CATOS is 8.4(11)GLX. The...

    Devnul0 pointsBadges:
  • Cisco Routers ios

    on a cisco router i have two ethernet conetions how can i make them one ip address for fault tolerance

    Crog115970 pointsBadges:
  • g.729 3rd party VOIP on Cisco routers QoS – am I doing it right?

    Hi, I am unsure about which configs are sufficient for implementing QoS on 2 2600 series routers over a 2MB serial link. On one side is the IP pbx and there are up to 6 IP phones plugged into a switch on the other side. We are using a non-cisco VoIP product using g.729. From what I can see all I...

    Robbieg0 pointsBadges:
  • Configuration Backup for Cisco Switches

    Hi, I have approx 20 cisco catalyst 2950 switches, and would like to be able to copy startup config into a tftp server on a monthly basis. Does anyone know if the IOS is capable of sheduling the copy command, or has anyone written perl or shell scripts to automate this process. ? Any Help Is...

    DerekKing0 pointsBadges:
  • Configure an EtherChannel between 2 switches and a server

    I have a customer wanting me to do a couple of things that I need clarification on. First I have an existing catalyst 4006 switch that we are adding a new module to (mod 6). We also are putting in a new switch (catalyst 2948). The customer is wanting to trunk the 4006 to the 2948 on ports: on the...

    Hocmat230 pointsBadges:
  • Connecting Cisco Switches Back-to-Back Through the Console Ports

    Hi. I'm trying to find a way to connect 2 Cisco switches (could be 2x2950, 2x3560, or a mix of those) from console port to console port via Reverse Telnet. Any idea if it can be done; if so how can I do it?

    Atomas0 pointsBadges:
  • Setup Partial global Notes Address Book replication

    How to add values to the NAB on one server, but these changes not to replicate to the other servers. So one NAB would have more fields than the rest of them. This is because we need to use Cisco Unity with Lotus Notes, but is not going to be implemented through the whole organization.

    Rfuentesd0 pointsBadges:
  • Cisco 9124E Fabric Switch for HP c-Class Bladesystem install?

    Has anyone out there set one of these up in an established SAN?

    QueenofT0 pointsBadges:
  • VoIP VLAN over bridge

    I am extending a subnet over T1 bridge using Adtran 3205 routers. The host site is connected via Cisco 2801 router with a switch card to th e HQ site. The remote site is connected to the host site by the bridged Adtran's. The switch at the remote site is a Cisco C2960. I connected a PC to the...

    Gforsythe75 pointsBadges:
  • VPN Passthrough on CISO 2800

    To anyone that can help. I have a ciso 2800 whith an adsl card connecting to a normal adsl connection. At the moment people cannot connect to external VPN Servers thorugh the router. Where do I configure this to allow VPN Passthrough traffic. I have tried created ACL to allow ports 50, 51, 1723 &...

    Rounds198160 pointsBadges:
  • Accessing Internet through two ISPs

    We have a 512 kbps link Internet connection from an ISP say ISP1. We are connected to the Internet through a DLINK DI-804HV router and a DLINK DFL-300 Firewall. Now we want to enhance our speed from 512 kbps to 1 Mbps. But instead of enhancing the same link, we are planning to get another 512 kbps...

    Ams7535 pointsBadges:
  • NAT on a Cisco 3524XL layer 2 switch

    Is it possible to use NAT on a Cisco 3524 switch? If so is it possible to see a sample template? Thanks Steve

    Devnul0 pointsBadges:
  • Wake-On-LAN / Cisco Mac address-tables

    Recently I scheduled my computers to power on using Wake-On-LAN. There seems to be an issue with some of the computers not turning on. All the computers have identical hardware and have the same BIOS settings. I did some investigation and I noticed that the computers that were not turning on did...

    Skepticals0 pointsBadges:
  • Routing Between Subnets and between networks

    1.I have two separe networks 192.168.0.0 and 192.168.1.0 ,they r physicall connected. What should i configure and where to configure so that host of each network can connect to other host in other network. 2.I have two separe Subnets(after subnetting a class B network),they r physicall connected....

    Chinmoymohanty0 pointsBadges:
  • Networking DHCP growth

    Okay, probably a simple question for a lot, but my experience has been more along the lines of many offices, with a typical setup of a border router (cisco, firewall (watchguard, new cisco ASA's, Windows 2003 server DC, exchange server, etc....) I have been doing this a while now and have been...

    Kevins740 pointsBadges:
  • Cisco Load sharing with port forwarding different ISP’s

    I have a 1811 series router now its set with dual internet connections two different ISP's I have 2 default routes basically It should load balance between two now my concern is I need a port forwarding as we use privite space addressing. I am including current config addresses have been changed to...

    Dimchik0 pointsBadges:
  • Cisco 3640 config issue

    I'm migrating from a 2620 to a 3640 carrying 2 multilinked T-1 circuits and a single Ethernet interface. The 2620 is running IOS 12.2 and 12.4 is on the 3640. I have ported over the configuration almost identically, but the 3640 won't move traffic despite showing all interfaces up/up and showing no...

    MitchFF0 pointsBadges:
  • SECURE FTP SITE ON Windows 2003

    We have a Windows 2003 IIS server setup behind our firewarll which is a PIX firewall. What is the best method to establish a secure FTP site on this IIS server? I have reviewed this topic on the internet and actually talked with somebody from IPSWITCH and the best method available is to purchase a...

    Mconfer0 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following