Cisco pix vpn access
I have 1 main office and 3 remote offices connected by Cisco Pix’s. The main server and email server are in the main office. As long as the computers are on the network everything is fine. The main office has a vpn set up for remote users and it works fine. The other offices want [...]

Answer Question   |  March 13, 2008  10:41 PM
Cisco, PIX, VPN

What’s broadcasting and which switch will fix timed-out requests?
I am an Internet distributor of Exatt.net. When my customer pings the gateway it gives me lots of timed-out requests. Exatt.net says it broadcasts in your network. What does this mean, and how can I fix my timed-out requests? I use a hub. Someone told me to use a management switch, but I have no [...]

Answer Question   |  May 5, 2008  6:35 PM
Broadcast, Cisco, Exatt.net, Networking, Switches

CCNA need to know Dos Command line/Registry/shell script???
For any of Cisco certification job , do we need to know how to do DOS commmand line, fixing registry and writing shell script??? What I actually want to know is does cisco people only dealing with Physical side of newtork such as switch, routing & network configuration. do they need to know much of [...]

Answer Question   |  February 16, 2011  1:26 AM
CCNA, Certifications, Cisco, Networking certifications

Locked out of Cisco Router – Password reset doesn’t work
do work for a local non-profit group. Apparently some prior network admin left under unhappy circumstances and did something to the cisco router(s) there. We had no password access, so I went through the password recovery/reset procedure. Everything seemed to be fine except for two little details: 1) The password change had no noticeable effect [...]

Answer Question   |  November 1, 2010  4:34 PM
Cisco, Cisco Routers, Network security, Password, Routers

Cisco 1310 point to point wireless bridge with WPA2
Tried using the document provided on the Cisco website to create a point to point wireless bridge and it works fine with WEP encryption, but how do I get the WPA2 encryption to work since WEP is not secure ? I also found a document on the Cisco site about WPA2 encryption but that is [...]

Answer Question   |  March 8, 2008  7:23 PM
Bridges, Cisco, Cisco 1310, WEP, WPA2

how to configure your cisco router to dial remote server has isdn modem
hi : i have 2811 cisco router with bri interface , and i want to know away to make this router call remote server has isdn modem , but all the ways didnot works , can any one help me with that and i;ll be thankfull plz

Answer Question   |  March 3, 2008  1:23 PM
Cisco, ISDN, Routers

ONS15454
I need to test OC-48-LR1550 CIRCUIT PACKS AND I DO NOT HAVE TRUE ACCESS TO THE TL1 COMMAND LINE.

Answer Question   |  February 26, 2008  6:20 PM
Cisco, Telecom

Cisco pix501 VPN at home.
A question submitted on SearchNetworking.com I just got IPSEC passthru working. IPSEC passthru is the most important feature because from home I have to VPN back to ASA at work. I would also like when I’m at work to VPN back to my home (VPN the other way that terminates on my pix 501) This [...]

Answer Question   |  February 27, 2008  5:35 PM
Cisco, Cisco PIX, Firewalls, IPsec, PIX, VPN

OSI and Cisco
differences and similarities between thye OSI reference model and the Cisco hierarchial model and how they are used

Answer Question   |  February 25, 2008  11:36 PM
Cisco, Hierarchical Internetworking Model, OSI Model

vpn client for PDA in a Cisco system
I had been using Movian VPN on an I-mate jam, which worked fine untill Cisco stopped supporting it. I have now changed to an HTC P3600i, does any one know if there is a VPN available that will work with this phone linking to a Cisco Systems VPN Client

Answer Question   |  February 5, 2008  5:15 AM
Cisco, PDA, VPN

VOIP help
I have avaya voip phones on my network and I need to setup an ip helper to get them over to a particlaur vlan. The reason is that if they go down they can not find their config info. What should the statement on the Cisco router look like

Answer Question   |  January 31, 2008  7:36 PM
Avaya, Cisco, VoIP

Cisco IOS default config not seen in running or startup configs
Is there a list of commands that do not show up in the running or startup configurations that are default. I am trying to locate the commands that are not visible in startup or running configs in 12.2 or newer IOS.

Answer Question   |  January 23, 2008  7:02 PM
Cisco, Cisco IOS

bind 3rd ip in fast ethernet
I want to baind one more ip in fastether nat i have baind allready two ips i want one more how can i baind one more ip in router cisco 1700 series routher

Answer Question   |  December 20, 2007  9:02 AM
Cisco, IP addressing, Routers

Cisco Catalyst 3750 routing issues
I need help configuring a simple routing scheme for a 3750, I have a visio diagram of a very simple network, let me know if anybody can help. thanks

Answer Question   |  December 21, 2007  6:29 PM
Cisco, Cisco Catalyst 3750, Routers

Cisco Aironet 1200 Ap
can this unit be used to receive a wireless internet signal then re-transmit or laptops and other wireless end users

Answer Question   |  December 19, 2007  6:22 PM
Access Points, Cisco, Cisco Aironet, Network, Wireless

cisco
what is cisco networking and what are the different considerations in designing a network?

Answer Question   |  December 17, 2007  6:48 AM
Cisco, Network design

Swithces
Can I assign two ip addresses in a cisco switch port?

Answer Question   |  November 17, 2009  10:02 AM
Cisco, IP addressing, Switches

Cisco related query!!
Hi friends, I am suman.I am working as Business Manager for a cisco partner.I am into business development.I am following a set of principles to reach my goals/target.Can you suggest what are the better options to go into the market more efficiently. How it would be if I am CCNA certified amd Will there be [...]

Answer Question   |  February 16, 2011  5:58 AM
CCNA, Cisco, Networking

tagging ports on cisco switch
I have configured a 3750 switch to communicate to a 3550 switch and I set up vlans and I trunked the uplink ports. I am told that I should configure the ports for tagging, I am not sure what the tagging will do for me and if it is really needed. Please explain tagging. tks [...]

Answer Question   |  November 30, 2007  5:54 AM
Cisco, Networking Equipment, Switches

cisco os erase me 3400
hi i am having cisco me 3400 switch by mistake i erase cisco os now the prb is i am unable to get enable mode how can i get enable mode pls help me in this reg masood ali

Answer Question   |  February 21, 2008  6:53 AM
Cisco, cisco os erase, Switches