• Do I have to use proxy with PIX firewall?

    i have pix 515E firewall and cyber roam device which is using as a proxy.do i have to use proxy with pix firewall

    Intrnetworking30 pointsBadges:
  • Cisco ASA5510

    I need to find out if there is a command to shutdown Cisco ASA5510 firewall rather then walking up to the firewall and pulling the power plug ... thanks

    Kwt712555 pointsBadges:
  • Swithces

    Can I assign two ip addresses in a cisco switch port?

    Abena5 pointsBadges:
  • How should i segment this?

    Hi, I have been given a project which basically entails segmenting hotel rooms in a hotel, on the network. The hotel is not built yet so im going to say for arguments sake there are 8 rooms on every floor, and there are 7 floors. Inside the rooms are various devices with Ethernet connectivity (a...

    LaurenceS15 pointsBadges:
  • What is the difference between a network module and interface card

    Hi i want to know what is the difference between use a Network Module 1E1 or use ans WIC 1E1.   Thanks

    Quiensoy5 pointsBadges:
  • cisco 1721 router install

    Our small company's new IT purchase was a Cisco 1721 router to be connected to 4 ports from our DSU/CSU T1 line. Currently we use a cable modem connection but I am trying to establish a second connection that users could take advantage of as well. My first goal is just to connect a desktop to the...

    Permits0 pointsBadges:
  • commands for nortel ARN router against cisco 1700 series router

    as i was using cisco router and now i want to installed nortel ARN router in place of that. I have configuration backup of cisco router,so i only want Nortel ARN router commands to configure against cisco commands

    Networkfresher5 pointsBadges:
  • Cisco 2811 Fast Ethernet and LAN configuration

    i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

    JACK15705 pointsBadges:
  • Adding a Route – Cisco router

    I have cisco 1800 series router that i want to add a route for all internet access is routed from the cable router/modem. Right now all the traffic is going over the T1 via cisco router. What i want to do is keep everything as is and only have the internet access route from the other devie. How...

    Kwt712555 pointsBadges:
  • Console Session on cisco router

    Hi                I have two routers in my lab , which  is not accessible via console. one is a cisco 3640 router, it shows some unrecognised characters when accessing via console. i did reset the baud rate jumper ,but no result.               In 2811 router it shows boot up...

    Puli45 pointsBadges:
  • BTS 10200 command definitions

    Are there definitions to the commands on the Cisco BTS 10200 switch whereby I can understand what each command input means

    VOIPEng5 pointsBadges:
  • Networking cisco access point

    i am working on cisco access point 1242 i had default username cisco and password Cisco but when i deleted and changed a new user name and password xxxx what happen, i can telnet through cli mode with new username and password but when i try to take http access the access point take old password...

    Ekansh400 pointsBadges:
  • QOS when receive traffic is more than transmit

    My current bandwidth is 10M. The traffic pattern is usually 2Mb transmit and 8 Mb receive from the ISP. I want to guarantee bandwidth for the WEBEX traffic which i can do for transmit traffic but my problem is that the receive traffic is whats killing me. Is there any way to make sure that my webex...

    Shane6505 pointsBadges:
  • No linestate on several CCM-lines that belongs to Cisco-SEP

    1) Can a SEP (Cisco phone) have several line connections? 2) If yes, what happens with the linestate of the lines if one line is restricted? 3) What does the below log mean? I want a linestate on ext 5228 but gets that line 5229 is restricted? Both lines is connected to same SEP. 2009-08-20...

    Runningisnew10 pointsBadges:
  • Two lines to one cisco-SEP

    What happens if there are two lines as extension mobility (user device profiles) connected/configured to one SEP where one of them is restricted? Does the other line inherit the restricted lines "configuration"?

    Runningisnew10 pointsBadges:
  • What are the similarities in Cisco and HP ProCurve switching protocols?

    like layer 2 protocol in cisco called VTP , while in hp procurve is called GARP , I need to know the other similarities in both for layer 2,3

    Henno5 pointsBadges:
  • Setting up Cisco 2950 switch

    Hello, New to itknowledge exchange... I have a hand me down Cisco 2950 12 port switch. I currently have assigned to my Cable Modem4 Static Public IP's Note: Not real but used for example. 70.66.131.1 70.66.131.2 70.66.131.3 70.66.131.4 I run 3 servers in my basement all of which I have configured...

    Perkster5 pointsBadges:
  • Cisco Access Control Lists – Recommended default template?

    Hey guys! I was hoping to find a default access control list template that you may use to block off, reserved addresses, known worms, viruses, vulnerabilities when you are setting up a new router? Trying to think of every possible threat is impossible but a good recommended starting point for...

    Tkrn10 pointsBadges:
  • .11n Experiences with various wireless AP vendors?

    I'm interested as to IT pros experiences with various wireless AP vendors: What equipment have you found to work well with the .11n standard, and what your experience has been like working with vendors. Were most willing to allow you to try-before-you buy for a major deployment?

    Michael Morisy8,598 pointsBadges:
  • Software based WIN Simulation

    Hi, I need to test out an application over WAN. The testing includes the response time with different delays and bandwidth requirements. Is there any piece of software (preferably opensource/freeware)which can simulate the WAN for me? The idea is to install two NICs in the Windows/Linux machine,...

    SADnBLUE0 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following